BMR Performance Lowering Springs Set - 1.25" Drop - Red (SP001R) - 1993-2002 GM F-Body
Dial in an aggressive, level stance and sharp handling precision with the Performance Lowering Springs Set (SP001R) from BMR Suspension. Custom-engineered for fourth-generation 1993-2002 GM F-Body platforms, this full set of four springs provides a matching 1.25-inch drop height across both the front and rear suspension. By swapping out your old or sagging factory coils, this kit effectively eliminates excessive wheel well gap and lowers your vehicle's center of gravity. This delivers a highly stable, flat-cornering stance that dramatically cuts down on body roll, hard brake dive, and rear-end acceleration squat without compromising daily ride comfort.
Every spring in the SP001R kit is engineered from premium high-tensile chrome silicon spring wire and cold-wound on advanced CNC coiling machinery to ensure absolute left-to-right uniformity. BMR utilizes a strict manufacturing process to guarantee long-lasting durability: each coil is pre-compressed solid twice at the factory to set its permanent height, stress-relieved at 750°F, and shot-peened to eliminate surface stress forces. This set features calibrated 550 lb/in linear front springs for crisp steering response paired with 160 lb/in dual-rate rear springs that optimize high-load handling and street compliance. Finished in a high-durability red powder coat and 100% computer load-tested, this set carries a lifetime warranty against spring sag.
IMPORTANT FITMENT & INSTALLATION NOTES:
- Chassis Compatibility: This specific four-spring kit is rated and matched for 1993-2002 GM F-Body rear-wheel-drive platforms (Camaro, Z28, SS, Firebird, Formula, Trans Am).
- Application Note: Performance-tuned specifically for street performance, pro-touring, and street/strip setups.
- Installation: Direct replacement for factory coils with an estimated installation window of 2-3 hours.
Features
- Fits 1993-2002 GM F-Body platforms
- Provides an even, matching 1.25-inch drop height across the front and rear
- Calibrated spring rates: 550 lb/in linear (Front) / 160 lb/in dual-rate (Rear)
- Manufactured from premium chrome silicon high-tensile spring wire
- Cold-wound on precise CNC coiling machines for perfect side-to-side uniformity
- Compressed solid twice during manufacturing to permanently establish ride height
- Stress-relieved at 750°F and shot-peened for maximum fatigue resistance
- 100% computer-tested for exact height and load capacity consistency
- Dramatically minimizes side-to-side body roll, wheel hop, and weight transfer
- Durable red powder coat finish protects against corrosion and road debris
- Backed by a robust lifetime warranty against spring sag
- Proudly designed and manufactured in the U.S.A.
Fitment
Chevrolet Camaro (4th Gen Platforms):
- 1993 Chevrolet Camaro (Base / Z28)
- 1994 Chevrolet Camaro (Base / Z28)
- 1995 Chevrolet Camaro (Base / Z28)
- 1996 Chevrolet Camaro (Base / Z28 / SS)
- 1997 Chevrolet Camaro (Base / Z28 / SS)
- 1998 Chevrolet Camaro (Base / Z28 / SS)
- 1999 Chevrolet Camaro (Base / Z28 / SS)
- 2000 Chevrolet Camaro (Base / Z28 / SS)
- 2001 Chevrolet Camaro (Base / Z28 / SS)
- 2002 Chevrolet Camaro (Base / Z28 / SS)
Pontiac Firebird / Formula / Trans Am (4th Gen Platforms):
- 1993 Pontiac Firebird / Formula / Trans Am
- 1994 Pontiac Firebird / Formula / Trans Am
- 1995 Pontiac Firebird / Formula / Trans Am
- 1996 Pontiac Firebird / Formula / Trans Am
- 1997 Pontiac Firebird / Formula / Trans Am
- 1998 Pontiac Firebird / Formula / Trans Am
- 1999 Pontiac Firebird / Formula / Trans Am
- 2000 Pontiac Firebird / Formula / Trans Am
- 2001 Pontiac Firebird / Formula / Trans Am
- 2002 Pontiac Firebird / Formula / Trans Am
CA Residents: WARNING: Cancer and Reproductive Harm www.P65Warnings.ca.gov
