Halltech Systems Stinger-RZ Cold Air Intake System - S&B Red Oiled Filter - NOMEX Sleeve - Stock Throttle Body - No PCV Hole in T/B Hose (2015 - 2019 Chevrolet Corvette C7 Z06) - STRZ06
Give your supercharged LT4 a less restrictive path to breathe with the Halltech Systems Stinger-RZ Cold Air Intake System. Engineered for the 2015-2019 Chevrolet Corvette C7 Z06, the STRZ06 combines Halltech's CAD-developed intake architecture with a sealed airbox substantially larger than stock and an induction path designed to reduce factory intake restriction. Halltech reports chassis-dyno testing by at least 20 independent shops, including GM dealerships, with reported gains ranging from 40 to 55 rear-wheel horsepower.
This STRZ06 configuration combines the S&B Red Oiled Filter with a NOMEX insulative sleeve, stock throttle-body connection, and a throttle-body hose without a PCV hole. It is configured for C7 Z06 owners retaining the stock throttle body while adding the NOMEX sleeve around the intake bridge for additional thermal insulation. The S&B Red Oiled Filter provides a serviceable oiled filtration setup for the Stinger-RZ system.
Specifications
- Manufacturer: Halltech Systems
- Part Number: STRZ06
- Product: Stinger-RZ Cold Air Intake System
- Vehicle: Chevrolet Corvette C7 Z06
- Model Years: 2015-2019
- Engine: 6.2L Supercharged LT4
- Filter Option: S&B Red Oiled Filter
- Filter Media: Oiled
- Throttle Body Configuration: Stock throttle body
- Throttle-Body Hose: No PCV hole
- Insulative Sleeve: NOMEX sleeve included
- Airbox: Sealed, larger-than-stock design
- Intake Development: CAD developed
- Reported Independent Dyno Gains: 40-55 RWHP
- Halltech Published Test Result: 51.6 RWHP
- Reported Quarter-Mile Improvement: 0.41 second ET and 6 mph
- Shipping Box Dimensions: 22 inches x 15 inches x 12 inches when shipped alone
- Shipping Box Weight: 9 pounds when shipped alone
- California Emissions Status: No California Executive Order number
Features
- Engineered for the 2015-2019 Chevrolet Corvette C7 Z06 with the supercharged LT4 engine
- CAD-developed Stinger-RZ cold air intake architecture
- S&B Red Oiled Filter included with this configuration
- Serviceable oiled filter media
- NOMEX insulative sleeve included with this configuration
- Configured for the stock C7 Z06 throttle body
- Throttle-body hose supplied without a PCV hole
- Sealed airbox is substantially larger than the factory unit to promote better airflow
- Designed to reduce airflow restriction from the factory filter and intake system
- Halltech reports independent chassis-dyno gains ranging from 40 to 55 RWHP
- Halltech publishes a 51.6 RWHP test result for the Stinger-RZ
- Halltech reports a 0.41-second quarter-mile ET improvement and 6 mph increase
- Compatible with Halltech's TRIC Ram Air package for a future induction upgrade
- Professional installation is strongly recommended by Halltech
- F-panel seal referenced in older installation material is no longer required or supplied with the kit
Proven Stinger-RZ Performance
The Stinger-RZ was developed to reduce airflow restriction ahead of the C7 Z06's supercharged LT4. Halltech reports that at least 20 independent shops, including GM dealerships, have chassis-dyno tested the system and recorded gains ranging from 40 to 55 RWHP. Halltech also publishes a 51.6 RWHP test result along with a reported quarter-mile improvement of 0.41 second and 6 mph. Actual results can vary based on vehicle condition, modifications, calibration, fuel, atmospheric conditions, and testing procedures.
S&B Red Oiled Filter
This STRZ06 configuration uses the S&B Red Oiled Filter, providing a serviceable oiled filtration option for the Stinger-RZ. It gives C7 Z06 owners a reusable performance-filter configuration designed to work as part of Halltech's complete Stinger-RZ induction system.
NOMEX Insulative Sleeve
This configuration includes the NOMEX insulative sleeve for the intake bridge. The sleeve adds an insulating barrier around the intake bridge, helping isolate the induction path from underhood heat while retaining the Stinger-RZ's high-flow intake configuration.
Stock Throttle Body Configuration
This version is configured for the stock C7 Z06 throttle body. It is intended for installations retaining the factory throttle-body size rather than using one of the larger 103mm or 112mm throttle-body configurations available for the Stinger-RZ.
No PCV Hole in Throttle-Body Hose
The throttle-body hose supplied with this configuration does not include a PCV hole. The hose configuration should be matched to the vehicle's PCV arrangement before installation to ensure the correct STRZ06 version is selected.
Larger Sealed Airbox
The Stinger-RZ uses a sealed airbox that Halltech describes as substantially larger than the factory unit to promote better airflow. The larger airbox requires repositioning some engine-bay components and making minor modifications during installation. Halltech strongly recommends professional installation.
TRIC Ram Air Compatible
The Stinger-RZ is designed so Halltech's TRIC Ram Air package can be added later without requiring changes to the Stinger-RZ intake system. This gives C7 Z06 owners the flexibility to install the cold air intake first and expand the induction system with the compatible TRIC Ram Air package later.
Emissions Notice
Halltech states that the STRZ06 does not have a California Executive Order number and is not legal for sale in California for use on emissions-controlled vehicles except where legally permitted for qualifying off-road applications such as track racing. Check applicable state and local emissions requirements before ordering or installing this intake.
Fitment
- 2015 Chevrolet Corvette C7 Z06 6.2L Supercharged LT4
- 2016 Chevrolet Corvette C7 Z06 6.2L Supercharged LT4
- 2017 Chevrolet Corvette C7 Z06 6.2L Supercharged LT4
- 2018 Chevrolet Corvette C7 Z06 6.2L Supercharged LT4
- 2019 Chevrolet Corvette C7 Z06 6.2L Supercharged LT4
FAQs
What does the NOMEX sleeve do on this Stinger-RZ?
The NOMEX sleeve provides an insulating barrier around the intake bridge to help isolate the induction path from underhood heat. This specific STRZ06 configuration includes the sleeve.
What configuration is included with this STRZ06?
This version includes the S&B Red Oiled Filter and NOMEX sleeve and is configured for the stock throttle body with no PCV hole in the throttle-body hose.
Get Your Halltech Stinger-RZ from Beefcake Racing
Upgrade your supercharged C7 Z06 with the Halltech Stinger-RZ STRZ06 configured with the S&B Red Oiled Filter, NOMEX sleeve, stock throttle-body setup, and non-PCV-hole throttle-body hose. For fitment or ordering questions, contact Beefcake Racing at sales@beefcakeracing.com or call 1-855-827-7223.
CA Residents: WARNING: Cancer and Reproductive Harm www.P65Warnings.ca.gov
