Halltech Systems Black Killer Bee MF108 Cold Air Induction - S&B Gray Oiled High Flow TRAK Filter - NOMEX Sleeve - Stock Throttle Body - PCV Hole in Hose (2006 - 2013 Chevrolet Corvette C6 LS7 Z06 / 2008 - 2013 Chevrolet Corvette C6 LS3) - KBMF108
Give your LS3 or LS7 C6 Corvette the increased airflow capacity of the Halltech Black Killer Bee MF108 Cold Air Induction while adding Halltech's NOMEX thermal protection. The MF108 uses a nominal 108 mm internal diameter at the MAF sensor, providing 9,161 square mm of cross-sectional area and approximately 10 percent more MAF area than the stock-size 103 mm configuration. This KBMF108 setup combines the performance-focused MF108 with an S&B Gray Oiled High-Flow Track Filter, NOMEX sleeve, stock C6 throttle-body connection, and a PCV hole in the throttle-body hose.
Halltech engineered the Killer Bee MF108 around a MAF-forward design with an integrated velocity stack built directly into the filter flange. The S&B Gray Oiled High-Flow Track Filter provides Halltech's track-oriented high-flow filter option, while the NOMEX sleeve creates an additional thermal barrier around the intake tube to help isolate it from engine-compartment heat. This version connects to the stock C6 throttle body using Halltech's Flex-Lock reducing hump hose and includes the PCV-hole provision. Because the MF108 increases MAF cross-sectional area over stock, proper MAF recalibration and tuning are required.
Specifications
- Manufacturer: Halltech Systems
- Product: Black Killer Bee MF108 Cold Air Induction
- Part Number: KBMF108
- MAF Internal Diameter: 108 mm
- MAF Cross-Sectional Area: 9,161 square mm
- MAF Area Increase: Approximately 10 percent greater than the stock-size 103 mm MAF section
- Filter: S&B Gray Oiled High-Flow Track Filter
- Filter Type: Oiled high-flow track filter
- Throttle Body Configuration: Stock C6 throttle body
- Throttle-Body Hose Intake End: 4.5 inches
- Throttle-Body Hose Throttle Body End: 4 inches
- Throttle-Body Hose Length: 3 inches
- Throttle-Body Hose Construction: Seven-layer NOMEX-reinforced silicone
- PCV Hose Configuration: PCV hole in throttle-body hose
- NOMEX Intake Sleeve: Included
- NOMEX Sleeve Length: 18 inches
- NOMEX Sleeve Material: Heat-resistant DuPont NOMEX aramid fabric with stretch elastomer
- Tuning Requirement: MAF recalibration and proper tuning required
- Intake Design: MAF-forward
- Filter Flange: Integrated velocity stack design
- Factory MAF Sensor: Transferred from the stock intake and not included
- Factory PCV Plastic Nipple: Transferred from the stock intake and not included
Features
- 108 mm MAF section designed for increased airflow capacity
- 9,161 square mm of MAF cross-sectional area
- Approximately 10 percent more MAF area than the stock-size 103 mm configuration
- MAF-forward architecture designed for excellent idle characteristics
- Integrated velocity stack built directly into the filter flange
- S&B Gray Oiled High-Flow Track Filter for a track-oriented high-flow filter configuration
- 18-inch Halltech NOMEX insulative sleeve included
- NOMEX aramid heat barrier helps isolate the intake tube from engine-compartment heat
- Halltech Flex-Lock reducing hump hose connects the 4.5-inch Killer Bee intake to the 4-inch stock C6 throttle body
- Seven-layer NOMEX-reinforced silicone throttle-body hose incorporates a compliant hump section and internal grip ridges
- PCV hole included in the throttle-body hose
- Designed as a tuning-required performance induction system for C6 LS3 and LS7 applications
Important Tuning and Installation Information
The Halltech Killer Bee MF108 requires proper tuning. Its nominal 108 mm internal diameter at the MAF sensor provides 9,161 square mm of cross-sectional area, approximately 10 percent more than the stock-size 103 mm MAF section. Because of this increase, proper MAF recalibration is required to establish the correct MAF transfer curve. Halltech also advises against cutting holes in the Corvette radiator shroud to direct additional air toward the filter because doing so can cause lean codes and surging.
Fitment
- 2006 Chevrolet Corvette C6 Z06 7.0L LS7
- 2007 Chevrolet Corvette C6 Z06 7.0L LS7
- 2008 Chevrolet Corvette C6 Z06 7.0L LS7
- 2009 Chevrolet Corvette C6 Z06 7.0L LS7
- 2010 Chevrolet Corvette C6 Z06 7.0L LS7
- 2011 Chevrolet Corvette C6 Z06 7.0L LS7
- 2012 Chevrolet Corvette C6 Z06 7.0L LS7
- 2013 Chevrolet Corvette C6 Z06 7.0L LS7
- 2008 Chevrolet Corvette C6 6.2L LS3
- 2009 Chevrolet Corvette C6 6.2L LS3
- 2010 Chevrolet Corvette C6 6.2L LS3
- 2011 Chevrolet Corvette C6 6.2L LS3
- 2012 Chevrolet Corvette C6 6.2L LS3
- 2013 Chevrolet Corvette C6 6.2L LS3
FAQs
Does the Halltech Killer Bee MF108 KBMF108 require tuning?
Yes. Halltech requires tuning for the MF108. Its 108 mm MAF section provides 9,161 square mm of cross-sectional area, approximately 10 percent more than the stock-size 103 mm MAF section. Proper MAF recalibration is required so the engine management system accurately accounts for airflow through the larger intake.
What is included in this KBMF108 configuration?
This configuration combines the black Halltech Killer Bee MF108 with an S&B Gray Oiled High-Flow Track Filter, Halltech NOMEX intake sleeve, stock C6 throttle-body connection, and a PCV hole in the throttle-body hose. The stock throttle-body connection uses Halltech's 4.5-inch to 4-inch Flex-Lock reducing hump hose.
Why Buy Halltech Systems from Beefcake Racing?
Beefcake Racing is your source for Halltech Systems Corvette performance parts, with knowledgeable support to help you match the correct intake, filter, throttle-body configuration, and supporting components to your build. Questions about the Halltech Killer Bee MF108 or your C6 Corvette combination? Contact Beefcake Racing at sales@beefcakeracing.com or call 1-855-827-7223.
CA Residents: WARNING: Cancer and Reproductive Harm www.P65Warnings.ca.gov
