Fuel Injector Clinic 1200cc High-Z Fuel Injector Set (ish01-1200h) - Holley GM and Ford
Give your high-performance Holley GM or Ford fuel system the precise, consistent fuel delivery it needs with the Fuel Injector Clinic 1200cc High-Z Fuel Injector Set. Part number ish01-1200h includes eight saturated, high-impedance injectors rated at 1200cc/min (110 lbs/hr) at 43.5 PSI and 1350cc/min (130 lbs/hr) at the OE 58 PSI fuel pressure. Designed for excellent linearity and repeatable short pulse width operation, these injectors deliver the control tuners need for strong drivability at low pulse widths while providing substantial fuel capacity when the engine is under load.
Fuel Injector Clinic precisely flow matches each injector set to within 1%. Every injector is individually numbered, and its results are documented on the detailed flow sheet supplied with the set. FIC tests and rates its high-performance injectors at 43.5 PSI (3 Bar) and 90 degrees F fuel temperature using CF-16B calibration fluid. Tight manufacturing tolerances and superior short pulse width control help make the ish01-1200h predictable to tune while maintaining the consistency demanded by serious performance combinations.
Specifications
- Manufacturer: Fuel Injector Clinic
- Part Number: ish01-1200h
- Application: Holley GM and Ford
- Injector Quantity: 8
- Injector Type: Saturated / High Impedance (High-Z)
- Flow Rate at 43.5 PSI: 1200cc/min (110 lbs/hr)
- Flow Rate at OE 58 PSI: 1350cc/min (130 lbs/hr)
- Test Pressure: 43.5 PSI (3 Bar)
- Test Fuel Temperature: 90 degrees F
- Calibration Fluid: CF-16B
- Flow Matching: Precisely matched to within 1%
- Injector Identification: Individually numbered
- Flow Documentation: Detailed injector flow sheet included
- Pigtails: Included for wiring harness plug conversion
- Plug-and-Play Adaptors: Optional
- O-Rings: Required application-specific O-rings included
- Warranty: Lifetime warranty against failure caused by defects in original manufacture
Features
- Eight 1200cc/min high-performance fuel injectors
- Flows 110 lbs/hr at 43.5 PSI fuel pressure
- Flows 130 lbs/hr, or approximately 1350cc/min, at OE 58 PSI fuel pressure
- Saturated, high-impedance High-Z injector design
- Excellent linearity for predictable fuel delivery
- Superior short pulse width control and repeatability
- Precisely flow matched to within 1%
- Each injector is individually numbered with results supplied on a detailed flow sheet
- Flow tested at 43.5 PSI and 90 degrees F using CF-16B calibration fluid
- Tight manufacturing tolerances support easier tuning and excellent drivability
- Brand-new, unused injectors rather than remanufactured or core-program injectors
- Includes pigtails for the required injector connector conversion
- Optional plug-and-play adaptors eliminate the need to cut and solder the vehicle harness
- Includes the required O-rings for the intended application configuration
- Backed by Fuel Injector Clinic's lifetime warranty against manufacturing defects
Injector Plug and Wiring Requirements
The ish01-1200h injector set requires an injector plug conversion at the vehicle wiring harness. The included pigtails can be soldered into the harness to replace the existing injector plugs. For an installation that does not require cutting or soldering the harness, optional plug-and-play adaptors can be purchased to convert the injector connection to the appropriate harness connection.
This connector conversion allows Fuel Injector Clinic to use brand-new, unused injectors for its performance applications rather than relying on remanufactured or core-program injectors. For aftermarket fuel systems or other non-standard installations, contact Beefcake Racing before ordering so the injector configuration and connection requirements can be confirmed for your setup.
Fitment
- Holley GM applications
- Holley Ford applications
FAQs
What does the 1200cc rating of the Fuel Injector Clinic ish01-1200h mean?
The injectors are rated at 1200cc/min, or 110 lbs/hr, at 43.5 PSI (3 Bar) fuel pressure. At the OE 58 PSI (4 Bar) fuel pressure referenced for this application, they flow approximately 1350cc/min, or 130 lbs/hr.
Does the ish01-1200h require injector wiring changes?
Yes. The injector plug must be converted. Pigtails are included and can be soldered into the existing wiring harness, or optional plug-and-play adaptors can be used to make the connection without cutting or soldering the harness.
Order Your Fuel Injector Clinic Injectors from Beefcake Racing
Whether you are building a serious street combination or a high-output performance setup, getting the injector size and configuration right is critical. Beefcake Racing can help you confirm the Fuel Injector Clinic injector setup that matches your Holley GM or Ford combination before you order. For product questions or help with your fuel system, email sales@beefcakeracing.com or call 1-855-827-7223.
CA Residents: WARNING: Cancer and Reproductive Harm www.P65Warnings.ca.gov
