Fuel Injector Clinic 365cc High-Z Fuel Injector Set (ish01-0365h) - Holley GM and Ford
Upgrade your Holley GM or Ford EFI fuel system with the precision and consistency of the Fuel Injector Clinic 365cc High-Z Fuel Injector Set. Part number ish01-0365h includes eight saturated, high-impedance injectors rated at 365cc/min (35 lbs/hr) at 43.5 PSI and approximately 420cc/min (40 lbs/hr) at OE 58 PSI fuel pressure. Excellent linearity and repeatable short pulse width operation provide the controlled fuel delivery tuners need for responsive drivability and predictable performance.
Fuel Injector Clinic precisely flow matches each injector set to within 1%. Every injector is individually numbered, with its results documented on the detailed flow sheet supplied with the set. FIC flow tests and rates its high-performance injectors at 43.5 PSI (3 Bar) and 90 degrees F fuel temperature using CF-16B calibration fluid. Superior short pulse width control and tight manufacturing tolerances help make the ish01-0365h easy to tune while delivering consistent fuel distribution across all eight cylinders.
Specifications
- Manufacturer: Fuel Injector Clinic
- Part Number: ish01-0365h
- Application: Holley GM and Ford EFI intake applications, excluding Holley GM composite manifolds
- Injector Quantity: 8
- Injector Type: Saturated / High Impedance (High-Z)
- Flow Rate at 43.5 PSI: 365cc/min (35 lbs/hr)
- Flow Rate at OE 58 PSI: 420cc/min (40 lbs/hr)
- Test Pressure: 43.5 PSI (3 Bar)
- Test Fuel Temperature: 90 degrees F
- Calibration Fluid: CF-16B
- Flow Matching: Precisely matched to within 1%
- Injector Identification: Individually numbered
- Flow Documentation: Detailed injector flow sheet included
- Included Pigtails: PGTUSC8
- Optional Plug-and-Play Adaptors: PADPUtoJ8
- O-Rings: Required application-specific O-rings included
- Warranty: Lifetime warranty against failure caused by defects in original manufacture
Features
- Eight 365cc/min high-performance fuel injectors
- Flows 35 lbs/hr at 43.5 PSI fuel pressure
- Flows approximately 420cc/min, or 40 lbs/hr, at OE 58 PSI fuel pressure
- Saturated, high-impedance High-Z injector design
- Excellent linearity for consistent and predictable fuel delivery
- Superior short pulse width control and repeatability
- Precisely flow matched to within 1%
- Each injector is individually numbered with results supplied on a detailed flow sheet
- Flow tested at 43.5 PSI and 90 degrees F using CF-16B calibration fluid
- Tight manufacturing tolerances support easier tuning and excellent drivability
- Brand-new, unused injectors rather than remanufactured or core-program injectors
- PGTUSC8 solder-in pigtails included
- Optional PADPUtoJ8 plug-and-play adaptors available
- Required O-rings included for the intended application configuration
- Backed by Fuel Injector Clinic's lifetime warranty against manufacturing defects
Injector Plug and Wiring Requirements
The ish01-0365h injector set requires an injector plug conversion when using the included PGTUSC8 pigtails. The pigtails can be soldered into the vehicle wiring harness to replace the existing injector plugs. For an installation that does not require cutting or soldering the harness, optional PADPUtoJ8 plug-and-play adaptors can be used to make the required connection.
This connector configuration allows Fuel Injector Clinic to supply brand-new, unused injectors for its performance applications rather than relying on remanufactured or core-program injectors. For aftermarket fuel systems, custom installations, or other non-standard setups, contact Beefcake Racing before ordering to confirm the correct injector configuration for your combination.
Fitment
- Holley GM EFI intake applications, excluding Holley GM composite manifolds
- Holley Ford EFI intake applications
FAQs
How much does the Fuel Injector Clinic ish01-0365h flow at 43.5 PSI and 58 PSI?
The ish01-0365h is rated at 365cc/min, or 35 lbs/hr, at 43.5 PSI (3 Bar). At OE 58 PSI (4 Bar) fuel pressure, the injectors flow approximately 420cc/min, or 40 lbs/hr.
Does the ish01-0365h require injector wiring changes?
When using the included PGTUSC8 pigtails, the existing injector plugs must be replaced and the new pigtails soldered into the wiring harness. Optional PADPUtoJ8 plug-and-play adaptors can instead be used to make the connection without cutting or soldering the vehicle harness.
Order Your Fuel Injector Clinic Injectors from Beefcake Racing
Getting the injector size, fitment, and connector configuration right is essential for a properly functioning performance fuel system. Beefcake Racing can help you confirm that the Fuel Injector Clinic ish01-0365h is the correct choice for your Holley GM or Ford EFI setup before you order. For product questions or help selecting your fuel injectors, email sales@beefcakeracing.com or call 1-855-827-7223.
CA Residents: WARNING: Cancer and Reproductive Harm www.P65Warnings.ca.gov
