Fuel Injector Clinic 2150cc Fuel Injector Set - High Z (is828-2150h) - Mercedes 6.3L V8
Feed a serious high-horsepower Mercedes 6.3L V8 with the massive fuel capacity and precise control of the Fuel Injector Clinic 2150cc High-Z Fuel Injector Set. Part number is828-2150h includes eight saturated, high-impedance injectors engineered for applications where extreme fuel demand must be balanced with excellent low pulse width control. Despite their massive 2150cc/min flow rate, these injectors are designed to deliver the response and controllability needed at idle and part throttle, giving tuners a powerful fueling solution for demanding Mercedes V8 builds.
Fuel Injector Clinic uses its proprietary Data Match Technology with dynamic flow matching during production of these high-flow injectors. This process significantly improves the ECU's ability to control the injectors in the sub-2ms pulse width range commonly encountered during idle and part-throttle operation. Each injector is individually serial numbered, and detailed flow matching and latency results are supplied on the included Data Match Sheet. The injectors are flow tested and rated at 43.5 PSI, or 3 Bar, with fuel temperature at 90 degrees F using CF-16B calibration fluid. PGTDEN8 solder-in pigtails are included for the required injector plug conversion.
Specifications
- Part Number: is828-2150h
- Injector Flow Rate: 2150cc/min
- Quantity: Set of 8 injectors
- Engine Application: Mercedes 6.3L V8
- Injector Type: Saturated / High Impedance
- Matching Technology: Fuel Injector Clinic Data Match Technology
- Matching Method: Dynamic flow matching
- Injector Identification: Individually serial numbered
- Injector Data: Data Match Sheet with flow matching and latency information
- Low Pulse Width Control: Optimized for improved ECU control in the sub-2ms range
- Test Pressure: 43.5 PSI / 3 Bar
- Test Fuel Temperature: 90 degrees F
- Calibration Fluid: CF-16B
- Included Pigtails: PGTDEN8
- Wiring Requirement: Injector plug conversion required
- Seals: Includes O-rings required for the listed factory application
- Fuel Restriction: Do not use with Q16, VP Import, or other MTBE oxygenated fuels
- Alcohol-Based Fuel Care: Follow FIC care instructions when using E85 or other alcohol-based fuels, particularly during prolonged periods of disuse
- Warranty: Lifetime warranty against failure caused by defects in original manufacture
Features
- Eight massive 2150cc/min High-Z fuel injectors for Mercedes 6.3L V8 applications
- Extreme fuel-flow capability for demanding high-horsepower combinations
- Saturated, high-impedance injector design
- Excellent low-end throttle response and short pulse width control for an injector of this size
- Dynamic Data Match Technology improves injector control in the sub-2ms pulse width range
- Precisely matched as a complete eight-injector set
- Each injector is individually serial numbered for identification and matching data
- Detailed Data Match Sheet supplies flow matching and latency information for accurate ECU calibration
- Flow tested and rated at 43.5 PSI / 3 Bar and 90 degrees F using CF-16B calibration fluid
- Includes PGTDEN8 solder-in pigtails for the required injector plug conversion
- Includes O-rings required for the listed factory application
- Backed by Fuel Injector Clinic's lifetime warranty against defects in original manufacture
Massive Fuel Delivery with Low Pulse Width Control
The challenge with an injector this large is not simply delivering enough fuel at wide-open throttle. The injector must also remain controllable when the engine requires only a fraction of its total capacity. Fuel Injector Clinic addresses this with dynamic flow matching designed specifically to improve ECU control below 2ms pulse width, where idle and part-throttle operation typically occur. The result is an injector built to combine enormous fuel-delivery capability with the precision required for proper calibration and drivability.
Part number is828-2150h requires an injector plug conversion and includes PGTDEN8 solder-in pigtails. If your Mercedes uses an aftermarket fuel rail or another non-standard fuel-system configuration, contact Beefcake Racing before ordering to verify proper fitment.
Important Fuel Compatibility Warning
Do not use the FIC 2150cc is828-2150h injectors with Q16, VP Import, or other MTBE oxygenated fuels. The internal construction of the 2150cc/min injector contains a seal that can swell after contact with MTBE, causing a significant reduction in injector flow. These injectors are therefore unsuitable for MTBE oxygenated fuels. When using E85 or other alcohol-based fuels, follow Fuel Injector Clinic's care instructions because prolonged disuse while the injectors are exposed to alcohol-based fuel can create potential corrosion issues.
Fitment
- Mercedes 6.3L V8 applications
FAQs
Can Fuel Injector Clinic is828-2150h 2150cc injectors be used with Q16 or VP Import?
No. These 2150cc injectors must not be used with Q16, VP Import, or other MTBE oxygenated fuels. MTBE can cause an internal seal to swell, significantly reducing injector flow. FIC also recommends following the applicable care instructions when using E85 or other alcohol-based fuels.
How can a 2150cc injector provide good idle and part-throttle control?
Fuel Injector Clinic uses dynamic Data Match Technology when producing these 2150cc injector sets. The matching process is designed to significantly improve ECU control in the sub-2ms pulse width range typically encountered during idle and part-throttle operation, helping provide the precise low pulse width control required from an injector with this much flow capacity.
Order Your Fuel Injector Clinic Injectors from Beefcake Racing
Beefcake Racing is your source for Fuel Injector Clinic injectors and supporting performance fuel-system components for serious Mercedes V8 builds. An injector with 2150cc/min of flow capacity demands proper fuel-system planning and calibration, and our experienced team can help you select the right injectors and supporting components for your combination.
Have questions about injector sizing, fuel compatibility, wiring, or fitment? Contact Beefcake Racing at sales@beefcakeracing.com or call 1-855-827-7223.
CA Residents: WARNING: Cancer and Reproductive Harm www.P65Warnings.ca.gov
