Fuel Injector Clinic 650cc Fuel Injector Set - High Z (is828-0650h) - Mercedes 6.3L V8
Upgrade the fueling capability of your Mercedes 6.3L V8 with the Fuel Injector Clinic 650cc High-Z Fuel Injector Set. Part number is828-0650h includes eight saturated, high-impedance ball and seat injectors engineered to deliver excellent linearity, repeatable short pulse width performance, and precise fuel delivery. For performance Mercedes V8 builds that demand more fuel without sacrificing low pulse width control and drivability, this matched FIC injector set provides the consistency tuners need from idle through wide-open throttle.
Fuel Injector Clinic precisely matches every set using its proprietary Data Match Technology. Each injector is individually serial numbered, and detailed flow matching and latency information is supplied on the included Data Match Sheet. The injectors are flow tested and rated at 43.5 PSI, or 3 Bar, with fuel temperature at 90 degrees F using CF-16B calibration fluid. PGTUSC8 solder-in pigtails are included for the required injector plug conversion, and FIC uses brand-new, unused injectors rather than remanufactured or core-program injectors.
Specifications
- Part Number: is828-0650h
- Injector Flow Rate: 650cc/min
- Quantity: Set of 8 injectors
- Engine Application: Mercedes 6.3L V8
- Injector Type: Saturated / High Impedance
- Injector Design: Ball and seat
- Matching Technology: Fuel Injector Clinic Data Match Technology
- Injector Identification: Individually serial numbered
- Injector Data: Data Match Sheet with flow matching and latency information
- Test Pressure: 43.5 PSI / 3 Bar
- Test Fuel Temperature: 90 degrees F
- Calibration Fluid: CF-16B
- Included Pigtails: PGTUSC8
- Wiring Requirement: Injector plug conversion required
- Seals: Includes O-rings required for the listed factory application
- Injector Condition: Brand-new, unused injectors
- Warranty: Lifetime warranty against failure caused by defects in original manufacture
Features
- Eight 650cc/min High-Z fuel injectors for Mercedes 6.3L V8 applications
- Saturated, high-impedance ball and seat injector design
- Excellent linearity for consistent and predictable fuel delivery
- Superior short pulse width control and repeatability for easier tuning and strong drivability
- Proprietary Data Match Technology precisely matches the injectors within the set
- Each injector is individually serial numbered for identification and matching data
- Detailed Data Match Sheet provides flow matching and latency information
- Flow tested and rated at 43.5 PSI / 3 Bar and 90 degrees F using CF-16B calibration fluid
- Includes PGTUSC8 solder-in pigtails for injector plug conversion
- Includes the O-rings required for the listed factory application
- Built using brand-new, unused injectors rather than remanufactured or core-program injectors
- Backed by Fuel Injector Clinic's lifetime warranty against defects in original manufacture
Precision-Matched Fuel Delivery for the Mercedes 6.3L V8
Adding fuel capacity is only worthwhile when the injectors can deliver that fuel consistently and predictably. Fuel Injector Clinic's 650cc injectors combine increased flow capability with excellent linearity and short pulse width repeatability, helping provide accurate fueling across the engine's operating range. FIC's Data Match Technology adds another level of precision by matching the injectors within the set and supplying detailed flow and latency information for proper ECU calibration.
Part number is828-0650h requires an injector plug conversion, and PGTUSC8 solder-in pigtails are included for replacing the existing injector connectors on the vehicle harness. If your Mercedes uses an aftermarket fuel rail or another non-standard fuel-system configuration, contact Beefcake Racing before ordering to verify proper injector fitment.
Fitment
- Mercedes 6.3L V8 applications
FAQs
Does the Fuel Injector Clinic is828-0650h injector set require wiring modifications?
Yes. The is828-0650h injector set requires an injector plug conversion. Fuel Injector Clinic includes PGTUSC8 solder-in pigtails with the set so the existing injector plugs on the vehicle wiring harness can be replaced.
How are the FIC is828-0650h 650cc injectors matched and tested?
Fuel Injector Clinic uses its proprietary Data Match Technology to precisely match the injectors within each set. Every injector is individually serial numbered, and matching and latency results are supplied on a Data Match Sheet. The injectors are flow tested and rated at 43.5 PSI, or 3 Bar, with fuel temperature at 90 degrees F using CF-16B calibration fluid.
Order Your Fuel Injector Clinic Injectors from Beefcake Racing
Beefcake Racing is your source for Fuel Injector Clinic injectors and performance fuel-system components for Mercedes V8 builds. Proper injector sizing and accurate calibration are critical when upgrading your fuel system, and our experienced team can help you choose the right injectors and supporting components for your combination.
Have questions about injector sizing, wiring, or fitment? Contact Beefcake Racing at sales@beefcakeracing.com or call 1-855-827-7223.
CA Residents: WARNING: Cancer and Reproductive Harm www.P65Warnings.ca.gov
