Fuel Injector Clinic 2150cc Fuel Injector Set - High Z (2006-2015 Mazda Miata MX-5 NC) (is602-2150h)
Support an extreme-performance 2006-2015 Mazda Miata MX-5 NC build with the Fuel Injector Clinic 2150cc High-Z Fuel Injector Set. Part number is602-2150h includes four massive 2150cc custom saturated, high-impedance ball and seat injectors engineered to deliver exceptional fuel volume without sacrificing the low-speed control required for a properly tuned performance car. Fuel Injector Clinic combines superior short pulse width control with its advanced Data Match Technology to give tuners precise, predictable injector operation across a wide operating range.
Because of the exceptional flow capacity of the 2150cc injector, Fuel Injector Clinic uses dynamic Data Match Technology during production to improve ECU control in the sub-2ms pulse width range commonly encountered during idle and part-throttle operation. Each injector is individually serial numbered, and the included Data Match Sheet provides detailed flow matching and latency information. FIC flow tests and rates these injectors at 43.5 PSI (3 Bar) with fuel temperature maintained at 90 degrees F using CF-16B calibration fluid. PGTDEN4 solder-in pigtails are included, or optional PADPDtoU4 plug-and-play adapters can be added for installation without cutting or soldering the factory harness.
Specifications
- Manufacturer: Fuel Injector Clinic
- Part Number: is602-2150h
- Injector Quantity: 4
- Flow Rating: 2150cc/min
- Injector Type: Custom saturated / high impedance
- Injector Design: Ball and seat
- Matching: Fuel Injector Clinic Data Match Technology dynamic flow matching
- FIC Test Pressure: 43.5 PSI (3 Bar)
- Test Fuel Temperature: 90 degrees F
- Calibration Fluid: CF-16B
- Included Pigtails: PGTDEN4
- Optional Plug-and-Play Adapters: PADPDtoU4
- MTBE Fuel Compatibility: Not compatible with Q16, VP Import, or other MTBE oxygenated fuels
- Seals: Includes the O-rings required for the listed factory application
- Warranty: Lifetime warranty against failure caused by defects in original manufacture
Features
- Four 2150cc high-impedance injectors for the 2006-2015 Mazda Miata MX-5 NC
- Massive fuel capacity for extreme-performance and high-fuel-demand applications
- Custom saturated, high-impedance ball and seat injector construction
- Excellent linearity and repeatable short pulse width operation
- Dynamic Data Match Technology provides precise injector set matching
- Improved ECU control in the sub-2ms pulse width range typical of idle and part-throttle operation
- Superior short pulse width control helps maintain tunability and drivability despite the exceptionally high flow capacity
- Each injector is individually serial numbered for identification and documentation
- Includes a Data Match Sheet with detailed flow matching and latency information
- Flow tested and rated at 43.5 PSI (3 Bar) with fuel temperature maintained at 90 degrees F
- Testing performed using CF-16B calibration fluid
- Includes PGTDEN4 solder-in pigtails
- Optional PADPDtoU4 plug-and-play adapters eliminate the need to cut or solder the factory injector wiring
- Supplied with the O-rings required for the listed factory application
- Covered by Fuel Injector Clinic's lifetime warranty against defects in original manufacture
Important Fuel Compatibility Warning
Do not use the is602-2150h injectors with Q16, VP Import, or other MTBE oxygenated fuels. The internal construction of the 2150cc injector includes a seal that has been found to swell when exposed to MTBE. This swelling can cause a significant reduction in injector flow, making these injectors unsuitable for MTBE oxygenated fuels.
These injectors can be used with alcohol-based fuels such as E85, but proper care is important. Fuel Injector Clinic warns of potential corrosion issues that can develop from prolonged disuse while the injectors remain exposed to alcohol-based fuel. Follow FIC's injector care instructions when operating or storing a vehicle using E85 or other alcohol-based fuels.
Massive Fuel Flow With Precise Low-Speed Control
Moving 2150cc/min is only part of what makes this injector effective in a serious performance build. An injector this large must also remain controllable at very short pulse widths if the car is expected to idle and drive properly. Fuel Injector Clinic's dynamic Data Match process is specifically used with these high-flow injectors to improve ECU control in the sub-2ms range. The result is the combination of massive fueling capability, precise matching, short pulse width control, and tunability needed for high-output NC Miata applications.
Wiring and Installation
The is602-2150h includes PGTDEN4 solder-in pigtails because an injector connector change is required for installation. The included pigtails can be soldered into the vehicle wiring harness in place of the existing injector connectors. For an installation that does not require cutting or soldering the factory harness, optional PADPDtoU4 plug-and-play adapters can be added.
Fuel Injector Clinic uses brand-new, unused injectors for its performance applications rather than relying on remanufactured or core-program injectors. The injectors are configured with the O-rings required for the listed factory application. If your Miata uses an aftermarket fuel rail or another non-standard fuel system configuration, contact Beefcake Racing before ordering to verify proper injector fitment.
Fitment
- 2006 Mazda Miata MX-5 NC
- 2007 Mazda Miata MX-5 NC
- 2008 Mazda Miata MX-5 NC
- 2009 Mazda Miata MX-5 NC
- 2010 Mazda Miata MX-5 NC
- 2011 Mazda Miata MX-5 NC
- 2012 Mazda Miata MX-5 NC
- 2013 Mazda Miata MX-5 NC
- 2014 Mazda Miata MX-5 NC
- 2015 Mazda Miata MX-5 NC
FAQs
Can Fuel Injector Clinic is602-2150h injectors be used with E85?
Yes. The 2150cc injectors can be used with E85, but Fuel Injector Clinic warns that prolonged disuse while exposed to alcohol-based fuels can create potential corrosion issues. Follow the manufacturer's injector care instructions when using or storing the vehicle with E85.
Can the is602-2150h injectors be used with Q16 or VP Import?
No. Do not use these injectors with Q16, VP Import, or other MTBE oxygenated fuels. MTBE can cause an internal seal to swell, significantly reducing injector flow.
Why Buy Fuel Injector Clinic Injectors From Beefcake Racing?
Beefcake Racing specializes in high-performance fuel system upgrades and can help you select the right injectors and supporting components for your Mazda Miata MX-5 build. With an injector as large as the FIC 2150cc, proper injector sizing, fuel selection, installation, and tuning are critical. Our performance specialists can help make sure you get the right components for your combination.
Email: sales@beefcakeracing.com
Phone: 1-855-827-7223
CA Residents: WARNING: Cancer and Reproductive Harm www.P65Warnings.ca.gov
