Fuel Injector Clinic 775cc High-Z Fuel Injector Set (IS412-0775H) - 2008-2014 Ford Falcon XR6T FG
Upgrade the fuel system in your Ford Falcon XR6T FG with a precisely matched injector package built to deliver increased fuel capacity without sacrificing the control and drivability that matter on a properly tuned performance car. The Fuel Injector Clinic IS412-0775H is a complete set of six 775cc/min saturated, high-impedance ball-and-seat injectors for the 2008-2014 Ford Falcon XR6T FG. Rated at 74 lbs/hr at 43.5 psi (3 Bar), these injectors combine increased fueling capability with excellent linearity and short pulse width repeatability for predictable tuning from idle through higher-load operation.
Each IS412-0775H set is precisely matched using Fuel Injector Clinic's proprietary Data Match Technology. Every injector is individually serial numbered, with detailed flow matching and latency results supplied on the included Data Match Sheet. FIC flow tests and rates the injectors at 43.5 psi (3 Bar) and 90 degrees F fuel temperature using CF-16B calibration fluid. PGTUSC6 solder-in pigtails are available with the set, or optional PADPUtoJ6 plug-and-play adapters can be selected for an installation without cutting or soldering the factory harness. Plug-and-play Ford ECU data is also available from Fuel Injector Clinic.
Specifications
- Manufacturer: Fuel Injector Clinic
- Part Number: IS412-0775H
- Application: 2008-2014 Ford Falcon XR6T FG
- Injector Quantity: Set of 6
- Flow Rate: 775cc/min
- Flow Rate at 43.5 psi: 74 lbs/hr
- Rated Fuel Pressure: 43.5 psi / 3 Bar
- Impedance: High impedance / High-Z
- Injector Type: Saturated ball-and-seat
- Injector Height: 53mm
- Top O-Ring: 14mm
- Bottom O-Ring Outer Diameter: 14mm
- Matching: Fuel Injector Clinic Data Match Technology
- Injector Identification: Each injector individually serial numbered
- Included Documentation: Data Match Sheet with flow matching and latency information
- Pigtail Option: PGTUSC6
- Optional Plug-and-Play Adapters: PADPUtoJ6
- Flow Test Pressure: 43.5 psi / 3 Bar
- Flow Test Fuel Temperature: 90 degrees F
- Calibration Fluid: CF-16B
- ECU Data: Plug-and-play Ford ECU data available from Fuel Injector Clinic
- O-Rings: Includes O-rings required for the listed factory application
- Warranty: Lifetime warranty against failure caused by defects in original manufacture
Features
- Complete set of six 775cc/min performance fuel injectors
- 74 lbs/hr flow rating at 43.5 psi (3 Bar)
- Saturated, high-impedance High-Z injector design
- Ball-and-seat injector construction
- Excellent injector linearity
- Superior short pulse width control and repeatability
- Designed for predictable tuning and strong drivability
- Precisely matched using Fuel Injector Clinic Data Match Technology
- Each injector individually serial numbered
- Includes Data Match Sheet with detailed flow matching and latency information
- Flow tested at 43.5 psi (3 Bar) and 90 degrees F
- Tested using CF-16B calibration fluid
- PGTUSC6 solder-in pigtail option
- Optional PADPUtoJ6 plug-and-play adapters
- Plug-and-play Ford ECU data available from Fuel Injector Clinic
- Includes O-rings required for the listed factory application
- Backed by Fuel Injector Clinic's lifetime warranty against manufacturing defects
775cc Performance for the Falcon XR6T FG
The IS412-0775H provides Falcon XR6T FG owners with increased injector capacity while maintaining the characteristics needed for precise calibration. Each injector flows 775cc/min, or 74 lbs/hr, at 43.5 psi (3 Bar), providing additional fueling capability for modified turbocharged combinations. Just as importantly, excellent linearity and repeatable injector operation help tuners maintain control throughout the engine's operating range rather than focusing solely on maximum injector flow.
Fuel Injector Clinic Data Match Technology
Consistent fuel delivery across all six cylinders becomes increasingly important as boost and engine output rise. Fuel Injector Clinic precisely matches each IS412-0775H set using its proprietary Data Match Technology. Every injector is individually serial numbered, and its results are documented on the included Data Match Sheet with detailed flow matching and latency information. This gives the tuner useful data about the actual injectors installed in the engine while helping support consistent cylinder-to-cylinder fueling.
Short Pulse Width Control and Drivability
A performance injector still has to behave accurately when the engine is idling, cruising, or operating under light load. During these conditions, the ECU commands much shorter injector pulse widths than it does under boost. The IS412-0775H combines excellent linearity with superior short pulse width control and repeatability, helping provide predictable fuel delivery during these low-load operating conditions. With proper calibration, that translates into the drivability expected from a street-driven XR6T while retaining the additional fuel capacity needed as engine demand increases.
PGTUSC6 Pigtails or PADPUtoJ6 Plug-and-Play Adapters
The IS412-0775H is available with PGTUSC6 solder-in pigtails or optional PADPUtoJ6 plug-and-play adapters. The PGTUSC6 option allows the appropriate injector connections to be installed on the vehicle wiring harness. Owners who prefer not to cut or solder the factory harness can select the PADPUtoJ6 adapters for a plug-and-play wiring solution.
Flow Tested for Accurate Calibration
Fuel Injector Clinic flow tests and rates these injectors at 43.5 psi (3 Bar) and 90 degrees F fuel temperature using CF-16B calibration fluid. Combined with Data Match Technology, individual injector serial numbering, and the supplied flow matching and latency information, this gives tuners valuable injector data for calibration. Plug-and-play Ford ECU data is also available from Fuel Injector Clinic.
Fitment
- 2008 Ford Falcon XR6T FG
- 2009 Ford Falcon XR6T FG
- 2010 Ford Falcon XR6T FG
- 2011 Ford Falcon XR6T FG
- 2012 Ford Falcon XR6T FG
- 2013 Ford Falcon XR6T FG
- 2014 Ford Falcon XR6T FG
FAQs
How much do the FIC IS412-0775H injectors flow?
The Fuel Injector Clinic IS412-0775H injectors flow 775cc/min, or 74 lbs/hr, at 43.5 psi (3 Bar) fuel pressure. The set contains six saturated, high-impedance ball-and-seat injectors precisely matched using Fuel Injector Clinic Data Match Technology.
What wiring options are available for the IS412-0775H injector set?
The IS412-0775H is available with PGTUSC6 solder-in pigtails or optional PADPUtoJ6 plug-and-play adapters. The PADPUtoJ6 adapters provide a wiring solution that avoids cutting or soldering the factory harness.
Upgrade Your Falcon XR6T with Beefcake Racing
Whether you're upgrading a responsive street-driven Falcon XR6T FG or building a higher-output turbo combination, Beefcake Racing can help you select the right Fuel Injector Clinic injectors and supporting fuel system components for your setup. Call 1-855-827-7223 or email sales@beefcakeracing.com for expert assistance.
CA Residents: WARNING: Cancer and Reproductive Harm www.P65Warnings.ca.gov
