Fuel Injector Clinic 1000cc High-Z Fuel Injector Set (IS411-1000H) - 2002-2010 Ford Falcon XR6T BA/BF
Upgrade the fuel system in your turbocharged Falcon with the Fuel Injector Clinic IS411-1000H 1000cc High-Z Fuel Injector Set. Designed for the Ford Falcon XR6T BA/BF application, this complete set of six saturated, high-impedance ball-and-seat injectors flows 1000cc/min, or 95 lbs/hr, at 43.5 psi (3 Bar). Built for performance combinations that demand substantially more fuel than a stock injector can provide, these FIC injectors combine high flow capacity with excellent linearity and short pulse width repeatability to give your tuner the predictable injector behavior needed for both power and drivability.
Every IS411-1000H set is precisely matched using Fuel Injector Clinic's proprietary Data Match Technology. Each injector is individually serial numbered, and detailed flow matching and latency results are supplied on the included Data Match Sheet. FIC flow tests and rates these injectors at 43.5 psi (3 Bar) and 90 degrees F fuel temperature using CF-16B calibration fluid. The set is available with PGTUSC6 solder-in pigtails or optional PADPUtoJ6 plug-and-play adapters, giving you a choice between a permanent connector conversion and an adapter-based installation without cutting or soldering the factory harness.
Specifications
- Manufacturer: Fuel Injector Clinic
- Part Number: IS411-1000H
- Application: Ford Falcon XR6T BA/BF
- Injector Quantity: Set of 6
- Flow Rate: 1000cc/min
- Flow Rate: 95 lbs/hr at 43.5 psi
- Rated Fuel Pressure: 43.5 psi / 3 Bar
- Impedance: High impedance / High-Z
- Injector Type: Saturated ball-and-seat
- Matching: Fuel Injector Clinic Data Match Technology
- Pigtail Option: PGTUSC6
- Optional Plug-and-Play Adapters: PADPUtoJ6
- Flow Test Pressure: 43.5 psi / 3 Bar
- Flow Test Fuel Temperature: 90 degrees F
- Calibration Fluid: CF-16B
- ECU Data: Plug-and-play Ford ECU data available from Fuel Injector Clinic
- O-Rings: Includes O-rings required for the listed factory application
- Warranty: Lifetime warranty against failure caused by defects in original manufacture
Features
- Complete set of six 1000cc/min performance fuel injectors
- 95 lbs/hr flow rating at 43.5 psi (3 Bar)
- Saturated, high-impedance High-Z design
- Ball-and-seat injector construction
- Excellent injector linearity
- Strong short pulse width repeatability
- Superior short pulse width control for accurate low-load fueling
- Designed to provide excellent tunability and drivability
- Precisely matched using Fuel Injector Clinic proprietary Data Match Technology
- Each injector is individually serial numbered
- Includes detailed Data Match Sheet with flow matching and latency information
- Flow tested at 43.5 psi (3 Bar) and 90 degrees F
- Tested using CF-16B calibration fluid
- PGTUSC6 solder-in pigtail option
- Optional PADPUtoJ6 plug-and-play adapters
- Plug-and-play Ford ECU data available from Fuel Injector Clinic
- Includes O-rings required for the listed factory application
- Backed by Fuel Injector Clinic's lifetime warranty against manufacturing defects
1000cc High-Z Performance for the Falcon XR6T
The IS411-1000H gives modified Falcon XR6T owners a substantial increase in injector capacity while retaining the control characteristics required for a properly calibrated performance engine. Each injector is rated at 1000cc/min, or 95 lbs/hr, at 43.5 psi (3 Bar). That combination of high flow, High-Z operation, excellent linearity, and repeatable short pulse width behavior makes this set well suited to performance builds where accurate fuel delivery matters across the entire operating range, not just at wide-open throttle.
Data Match Technology
A high-performance inline-six needs consistent fuel delivery from cylinder to cylinder, especially as airflow, boost, and fuel demand increase. Fuel Injector Clinic precisely matches the six injectors in each IS411-1000H set using its proprietary Data Match Technology. Every injector is individually serial numbered, and its results are documented on the included Data Match Sheet with detailed flow matching and latency information. This provides valuable injector data for calibration and helps your tuner work with a matched set rather than six injectors assumed to behave identically.
Short Pulse Width Control and Drivability
Injector performance at maximum flow is only part of the equation. A large injector also needs predictable behavior when the ECU commands very small amounts of fuel during idle, cruising, and throttle transitions. The IS411-1000H combines excellent linearity with strong short pulse width control and repeatability, helping provide the accurate fuel metering needed for good drivability while retaining the increased fuel capacity demanded by a modified XR6T.
PGTUSC6 Pigtails or PADPUtoJ6 Plug-and-Play Adapters
Fuel Injector Clinic offers two wiring solutions for the IS411-1000H. PGTUSC6 solder-in pigtails allow the injector connectors on the vehicle harness to be converted for the injectors. If you prefer an installation that does not require cutting or soldering the factory harness, optional PADPUtoJ6 plug-and-play adapters can be selected instead. This gives builders the flexibility to choose the installation method that best suits the vehicle and build.
Fitment
- 2002 Ford Falcon XR6T BA/BF
- 2003 Ford Falcon XR6T BA/BF
- 2004 Ford Falcon XR6T BA/BF
- 2005 Ford Falcon XR6T BA/BF
- 2006 Ford Falcon XR6T BA/BF
- 2007 Ford Falcon XR6T BA/BF
- 2008 Ford Falcon XR6T BA/BF
- 2009 Ford Falcon XR6T BA/BF
- 2010 Ford Falcon XR6T BA/BF
FAQs
How much do the FIC IS411-1000H injectors flow?
Fuel Injector Clinic currently rates the IS411-1000H at 1000cc/min, or 95 lbs/hr, at 43.5 psi (3 Bar) fuel pressure. The set contains six saturated, high-impedance ball-and-seat injectors matched specifically as a set using FIC Data Match Technology.
What wiring is required to install the IS411-1000H injectors?
The IS411-1000H is offered with PGTUSC6 solder-in pigtails or optional PADPUtoJ6 plug-and-play adapters. The pigtails allow the injector connectors on the harness to be converted, while the optional adapters provide a plug-and-play solution without cutting or soldering the factory wiring.
Upgrade Your Falcon XR6T Fuel System with Beefcake Racing
Building a modified or higher-output Ford Falcon XR6T requires a fuel system capable of keeping up with the engine's increased demand. Beefcake Racing can help you select the right Fuel Injector Clinic injectors and supporting fuel system components for your combination. Call 1-855-827-7223 or email sales@beefcakeracing.com for expert assistance.
CA Residents: WARNING: Cancer and Reproductive Harm www.P65Warnings.ca.gov
