Fuel Injector Clinic 650cc High-Z Fuel Injector Set (IS411-0650H) - 2002-2010 Ford Falcon XR6T BA/BF
Upgrade your turbocharged Falcon with the fuel capacity and precise injector control needed for a properly tuned performance build. The Fuel Injector Clinic IS411-0650H is a complete set of six 650cc/min saturated, high-impedance ball-and-seat injectors for the 2002-2010 Ford Falcon XR6T BA/BF. Rated at 650cc/min, or 62 lbs/hr, at 43.5 psi (3 Bar), these injectors provide increased fueling capability while maintaining the excellent linearity and short pulse width repeatability needed for accurate fuel delivery, responsive tuning, and strong drivability.
Every IS411-0650H set is precisely matched using Fuel Injector Clinic's proprietary Data Match Technology. Each injector is individually serial numbered, and detailed flow matching and latency results are provided on the included Data Match Sheet. FIC flow tests and rates these injectors at 43.5 psi (3 Bar) and 90 degrees F fuel temperature using CF-16B calibration fluid. PGTUSC6 solder-in pigtails are included, or optional PADPUtoJ6 plug-and-play adapters can be added for installation without cutting or soldering the factory harness. Plug-and-play Ford ECU data is also available from Fuel Injector Clinic.
Specifications
- Manufacturer: Fuel Injector Clinic
- Part Number: IS411-0650H
- Application: 2002-2010 Ford Falcon XR6T BA/BF
- Injector Quantity: Set of 6
- Flow Rate: 650cc/min
- Flow Rate: 62 lbs/hr at 43.5 psi
- Rated Fuel Pressure: 43.5 psi / 3 Bar
- Impedance: High impedance / High-Z
- Injector Type: Saturated ball-and-seat
- Matching: Fuel Injector Clinic Data Match Technology
- Included Pigtails: PGTUSC6
- Optional Plug-and-Play Adapters: PADPUtoJ6
- Flow Test Pressure: 43.5 psi / 3 Bar
- Flow Test Fuel Temperature: 90 degrees F
- Calibration Fluid: CF-16B
- ECU Data: Plug-and-play Ford ECU data available from Fuel Injector Clinic
- O-Rings: Includes O-rings required for the listed factory application
- Warranty: Lifetime warranty against failure caused by defects in original manufacture
Features
- Complete set of six 650cc/min performance fuel injectors
- 62 lbs/hr flow rating at 43.5 psi (3 Bar)
- Saturated, high-impedance High-Z injector design
- Ball-and-seat injector construction
- Excellent injector linearity
- Strong short pulse width repeatability
- Superior short pulse width control for accurate low-load fueling
- Designed for easy tuning and excellent drivability
- Precisely matched using Fuel Injector Clinic proprietary Data Match Technology
- Each injector is individually serial numbered
- Includes a Data Match Sheet with detailed flow matching and latency information
- Flow tested at 43.5 psi (3 Bar) and 90 degrees F
- Tested using CF-16B calibration fluid
- Includes PGTUSC6 solder-in pigtails
- Optional PADPUtoJ6 plug-and-play adapters available
- Plug-and-play Ford ECU data available from Fuel Injector Clinic
- Includes O-rings required for the listed factory application
- Backed by Fuel Injector Clinic's lifetime warranty against manufacturing defects
650cc Performance for the Falcon XR6T
The IS411-0650H provides increased injector capacity for modified Falcon XR6T applications while retaining the control characteristics needed for street-driven performance. Each injector is rated at 650cc/min, or 62 lbs/hr, at 43.5 psi (3 Bar). Combined with High-Z operation, excellent linearity, and repeatable short pulse width behavior, the increased flow gives tuners a strong foundation for accurately controlling fuel delivery as the engine's performance demands increase.
Data Match Technology
Consistent injector performance across all six cylinders is critical when tuning a performance turbocharged engine. Fuel Injector Clinic precisely matches every IS411-0650H set using its proprietary Data Match Technology. Each injector is individually serial numbered, and its results are documented on the included Data Match Sheet with detailed flow matching and latency information. This gives the tuner useful injector data while helping maintain consistent fuel delivery throughout the engine.
Short Pulse Width Control and Drivability
Injector performance is about more than maximum flow. A performance injector must also accurately meter small quantities of fuel during idle, cruising, part-throttle operation, and throttle transitions. The IS411-0650H combines excellent linearity with superior short pulse width control and repeatability, helping the ECU maintain predictable fuel delivery across a broad operating range. With proper calibration, that control helps retain the drivability expected from a street-driven XR6T while providing greater fueling capacity when engine load increases.
PGTUSC6 Pigtails or PADPUtoJ6 Plug-and-Play Adapters
The IS411-0650H includes PGTUSC6 solder-in pigtails for the required injector connector conversion. These allow the existing injector connections on the vehicle harness to be replaced with the correct connectors for the FIC injectors. For an installation that does not require cutting or soldering the factory wiring, optional PADPUtoJ6 plug-and-play adapters can be added instead. This gives XR6T owners the flexibility to choose the installation method that best fits their build.
Flow Tested and Matched as a Set
Fuel Injector Clinic flow tests these injectors at 43.5 psi (3 Bar) and 90 degrees F fuel temperature using CF-16B calibration fluid. More importantly, the six injectors are supplied as a matched set rather than simply grouped together based on nominal flow size. Combined with the included Data Match Sheet and available Ford ECU data, this gives builders and tuners the information needed to integrate the injectors into a properly calibrated performance fuel system.
Fitment
- 2002 Ford Falcon XR6T BA/BF
- 2003 Ford Falcon XR6T BA/BF
- 2004 Ford Falcon XR6T BA/BF
- 2005 Ford Falcon XR6T BA/BF
- 2006 Ford Falcon XR6T BA/BF
- 2007 Ford Falcon XR6T BA/BF
- 2008 Ford Falcon XR6T BA/BF
- 2009 Ford Falcon XR6T BA/BF
- 2010 Ford Falcon XR6T BA/BF
FAQs
How much do the FIC IS411-0650H injectors flow?
The Fuel Injector Clinic IS411-0650H injectors are rated at 650cc/min, or 62 lbs/hr, at 43.5 psi (3 Bar) fuel pressure. The package contains six saturated, high-impedance ball-and-seat injectors matched as a set using FIC Data Match Technology.
What wiring is required for the IS411-0650H injector set?
PGTUSC6 solder-in pigtails are included for converting the injector connections on the vehicle harness. Optional PADPUtoJ6 plug-and-play adapters can be added if you prefer to install the injectors without cutting or soldering the factory wiring.
Upgrade Your Falcon XR6T Fuel System with Beefcake Racing
Whether you're upgrading a street-driven XR6T or building a higher-output turbo combination, Beefcake Racing can help you select the right Fuel Injector Clinic injectors and supporting fuel system components for your setup. Call 1-855-827-7223 or email sales@beefcakeracing.com for expert assistance.
CA Residents: WARNING: Cancer and Reproductive Harm www.P65Warnings.ca.gov
