Fuel Injector Clinic 525cc High-Z Fuel Injector Set (IS411-0525H) - 2002-2010 Ford Falcon XR6T BA/BF
Upgrade your Ford Falcon XR6T with a precisely matched injector set engineered to deliver increased fuel capacity without sacrificing the control and drivability that matter on a street-driven turbo car. The Fuel Injector Clinic IS411-0525H is a complete set of six 525cc/min saturated, high-impedance ball-and-seat injectors for the 2002-2010 Ford Falcon XR6T BA/BF. Each injector flows 525cc/min, or 50 lbs/hr, at 43.5 psi (3 Bar), with flow increasing to 58 lbs/hr at 58 psi. Excellent linearity, short pulse width repeatability, and tight manufacturing tolerances help give tuners predictable injector behavior across the engine's operating range.
Fuel Injector Clinic precisely flow matches the six injectors in each IS411-0525H set to within 1 percent. Every injector is individually numbered, and its results are documented on the detailed flow sheet supplied with the set. FIC flow tests and rates these injectors at 43.5 psi (3 Bar) and 90 degrees F fuel temperature using CF-16B calibration fluid. PGTUSC6 solder-in pigtails are available with the set, or optional PADPUtoJ6 plug-and-play adapters can be selected for an installation without cutting or soldering the factory harness. Plug-and-play Ford ECU data is also available from Fuel Injector Clinic.
Specifications
- Manufacturer: Fuel Injector Clinic
- Part Number: IS411-0525H
- Application: 2002-2010 Ford Falcon XR6T BA/BF
- Injector Quantity: Set of 6
- Flow at 43.5 psi (3 Bar): 525cc/min / 50 lbs/hr
- Flow at 58 psi: 58 lbs/hr
- Impedance: High impedance / High-Z
- Injector Type: Saturated ball-and-seat
- Flow Matching: Precisely flow matched to within 1 percent
- Injector Identification: Each injector individually numbered
- Included Documentation: Detailed injector flow sheet
- Pigtail Option: PGTUSC6
- Optional Plug-and-Play Adapters: PADPUtoJ6
- Flow Test Pressure: 43.5 psi / 3 Bar
- Flow Test Fuel Temperature: 90 degrees F
- Calibration Fluid: CF-16B
- ECU Data: Plug-and-play Ford ECU data available from Fuel Injector Clinic
- O-Rings: Includes O-rings required for the listed factory application
- Warranty: Lifetime warranty against failure caused by defects in original manufacture
Features
- Complete set of six 525cc/min performance fuel injectors
- 50 lbs/hr flow rating at 43.5 psi (3 Bar)
- 58 lbs/hr flow at 58 psi fuel pressure
- Saturated, high-impedance High-Z injector design
- Ball-and-seat injector construction
- Excellent injector linearity
- Strong short pulse width repeatability
- Superior short pulse width control for accurate low-load fueling
- Tight manufacturing tolerances for consistent injector operation
- Designed for easy tuning and excellent drivability
- Injector sets precisely flow matched to within 1 percent
- Each injector individually numbered
- Detailed flow results supplied with each matched set
- Flow tested at 43.5 psi (3 Bar) and 90 degrees F
- Tested using CF-16B calibration fluid
- PGTUSC6 solder-in pigtail option
- Optional PADPUtoJ6 plug-and-play adapters
- Plug-and-play Ford ECU data available from Fuel Injector Clinic
- Includes O-rings required for the listed factory application
- Backed by Fuel Injector Clinic's lifetime warranty against manufacturing defects
525cc Performance for the Falcon XR6T
The IS411-0525H gives Falcon XR6T owners increased injector capacity while retaining the control characteristics required for a properly calibrated performance engine. Each injector flows 525cc/min, or 50 lbs/hr, at FIC's standard 43.5 psi (3 Bar) rating pressure. At 58 psi, flow increases to 58 lbs/hr. That combination of additional fuel capacity, High-Z operation, excellent linearity, and repeatable short pulse width behavior makes the set a strong upgrade for modified BA/BF XR6T applications that have outgrown their existing fueling capacity.
Precisely Flow Matched to Within 1 Percent
Fuel delivery needs to remain consistent across all six cylinders, especially as boost and engine output increase. Fuel Injector Clinic precisely flow matches each IS411-0525H injector set to within 1 percent rather than simply grouping six injectors of the same nominal size together. Every injector is individually numbered, and its results are listed on the detailed flow sheet supplied with the set. This gives builders and tuners useful information about the actual injectors going into the engine and helps support consistent cylinder-to-cylinder fueling.
Short Pulse Width Control and Street Drivability
Maximum flow capacity is only one measure of a performance injector. During idle, cruising, throttle transitions, and other low-load conditions, the ECU must command much smaller quantities of fuel. The IS411-0525H combines tight manufacturing tolerances with superior short pulse width control and repeatability, helping provide predictable fuel delivery when injector pulse widths are short. With proper calibration, that translates into the drivability and throttle response expected from a street-driven XR6T while retaining the additional capacity needed as engine load increases.
PGTUSC6 Pigtails or PADPUtoJ6 Plug-and-Play Adapters
The IS411-0525H is offered with PGTUSC6 solder-in pigtails or optional PADPUtoJ6 plug-and-play adapters. The PGTUSC6 option allows the appropriate injector connections to be installed on the vehicle harness. Builders who prefer an installation without cutting or soldering the factory wiring can select the PADPUtoJ6 plug-and-play adapters instead. This gives XR6T owners the flexibility to choose the wiring solution that best suits the vehicle and installation.
Flow Tested with CF-16B Calibration Fluid
Fuel Injector Clinic flow tests and rates these injectors at 43.5 psi (3 Bar) and 90 degrees F fuel temperature using CF-16B calibration fluid. Combined with precise flow matching, individual injector numbering, and the supplied flow data, this testing gives tuners a more useful foundation for calibration than relying on injector size alone. Plug-and-play Ford ECU data is also available from Fuel Injector Clinic to further support the tuning process.
Fitment
- 2002 Ford Falcon XR6T BA/BF
- 2003 Ford Falcon XR6T BA/BF
- 2004 Ford Falcon XR6T BA/BF
- 2005 Ford Falcon XR6T BA/BF
- 2006 Ford Falcon XR6T BA/BF
- 2007 Ford Falcon XR6T BA/BF
- 2008 Ford Falcon XR6T BA/BF
- 2009 Ford Falcon XR6T BA/BF
- 2010 Ford Falcon XR6T BA/BF
FAQs
How much do the FIC IS411-0525H injectors flow?
The Fuel Injector Clinic IS411-0525H injectors flow 525cc/min, or 50 lbs/hr, at 43.5 psi (3 Bar) fuel pressure. Fuel Injector Clinic also specifies a flow rate of 58 lbs/hr when operated at 58 psi.
What wiring options are available for the IS411-0525H?
The injector set is available with PGTUSC6 solder-in pigtails or optional PADPUtoJ6 plug-and-play adapters. The adapters provide an installation option that does not require cutting or soldering the factory wiring harness.
Upgrade Your Falcon XR6T Fuel System with Beefcake Racing
Whether you're upgrading a street-driven Falcon XR6T or building a higher-output turbo combination, Beefcake Racing can help you select the right Fuel Injector Clinic injectors and supporting fuel system components for your setup. Call 1-855-827-7223 or email sales@beefcakeracing.com for expert assistance.
CA Residents: WARNING: Cancer and Reproductive Harm www.P65Warnings.ca.gov
