Fuel Injector Clinic 775cc High-Z Injector Set (is408-0775h) - 2010-2014 Ford Raptor
Upgrade the fuel system in your 2010-2014 Ford Raptor with the Fuel Injector Clinic 775cc High-Z injector set. This matched set of eight injectors flows 775cc/min, or 74 lbs/hr, at 43.5 PSI fuel pressure, providing the additional fuel capacity needed for modified and high-performance Raptor combinations while maintaining the precise control required for excellent drivability. High-impedance ball and seat construction, excellent linearity, and strong short pulse width repeatability give your tuner predictable injector behavior across the operating range.
The is408-0775h combines serious performance capability with straightforward installation through plug-and-play compatibility with the OEM wiring harness. Each set is precisely matched using Fuel Injector Clinic's proprietary Data Match Technology, with every injector individually serial numbered and detailed flow matching and latency results supplied on the Data Match Sheet. FIC flow tests and rates these injectors at 43.5 PSI / 3 Bar and 90 degrees F fuel temperature using CF-16B calibration fluid. Plug-and-play Ford ECU data is available from Fuel Injector Clinic, and the set includes the O-rings required for the factory application.
Specifications
- Part Number: is408-0775h
- Injector Quantity: 8
- Flow Rate: 775cc/min
- Flow Rate at 43.5 PSI: 74 lbs/hr
- Fuel Pressure Rating: 43.5 PSI / 3 Bar
- Impedance: High impedance / saturated
- Injector Design: Ball and seat
- Electrical Connection: Plug-and-play fit to OEM harness
- Injector Matching: Fuel Injector Clinic Data Match Technology
- Calibration Fluid: CF-16B
- Test Fuel Temperature: 90 degrees F
- ECU Data: Plug-and-play Ford ECU data available from Fuel Injector Clinic
- O-Rings: Includes O-rings required for the factory application
- Warranty: Lifetime warranty against failure caused by defects in original manufacture
Features
- Complete matched set of eight 775cc/min performance fuel injectors
- 74 lbs/hr flow rating at 43.5 PSI fuel pressure
- Saturated high-impedance ball and seat injector design
- Increased fuel capacity for modified and high-performance Ford Raptor builds
- Excellent linearity for predictable fuel delivery
- Superior short pulse width control and repeatability
- Precisely matched using Fuel Injector Clinic Data Match Technology
- Each injector is individually serial numbered
- Data Match Sheet provides detailed flow matching and latency information
- Plug-and-play connection to the OEM injector harness
- No injector plug conversion required
- Flow tested and rated at 43.5 PSI / 3 Bar
- Tested at 90 degrees F fuel temperature using CF-16B calibration fluid
- Plug-and-play Ford ECU calibration data available from Fuel Injector Clinic
- Includes O-rings required for the factory application
- Designed for excellent tunability and drivability
- Backed by Fuel Injector Clinic's lifetime warranty against manufacturing defects
775cc Fuel Capacity for Performance Raptor Builds
As engine airflow and horsepower increase, injector capacity becomes increasingly important to maintaining proper fuel delivery under load. The FIC is408-0775h provides 775cc/min of flow per injector, giving modified Raptor combinations significantly greater fueling capability while retaining the accurate injector control needed during lower-demand operating conditions. It is a strong choice for builds that have moved beyond the capability of smaller injectors but still demand predictable street behavior.
Data Match Technology for Precise Tuning
Consistent injector performance across all eight cylinders is critical to a properly calibrated performance engine. Fuel Injector Clinic precisely matches each is408-0775h set using proprietary Data Match Technology. Every injector is individually serial numbered, and detailed flow matching and latency results are supplied on the Data Match Sheet. This provides your tuner with accurate injector-specific information to help achieve consistent cylinder-to-cylinder fueling and precise calibration throughout the operating range.
High Flow with Excellent Short Pulse Width Control
A performance injector must do more than deliver fuel at wide-open throttle. Accurate control during idle, cruising, and throttle transitions is equally important to drivability and tuning quality. Fuel Injector Clinic combines 775cc/min capacity with excellent linearity and superior short pulse width control, helping the ECU accurately meter fuel when demand is low while providing increased volume as engine load rises.
Plug-and-Play OEM Harness Installation
The is408-0775h is designed to connect directly to the OEM injector wiring harness on the listed Ford Raptor application. No injector plug conversion is required, eliminating the need for solder-in pigtails or electrical adapters and keeping installation clean and straightforward. Fuel Injector Clinic also includes the O-rings required for the factory application, while available plug-and-play Ford ECU data helps provide your tuner with the information needed for calibration.
Fitment
- 2010 Ford F-150 Raptor
- 2011 Ford F-150 Raptor
- 2012 Ford F-150 Raptor
- 2013 Ford F-150 Raptor
- 2014 Ford F-150 Raptor
Fitment Note: This injector set is designed for the title-listed 2010-2014 Ford Raptor application. If your truck uses aftermarket fuel rails or another non-standard fuel-system configuration, contact Beefcake Racing before ordering to verify proper injector fitment.
FAQs
Does the Fuel Injector Clinic is408-0775h require an injector plug conversion?
No. The is408-0775h provides plug-and-play compatibility with the OEM injector wiring harness for the listed 2010-2014 Ford Raptor application, so no injector plug conversion is required.
How are the FIC is408-0775h 775cc injectors matched and tested?
Fuel Injector Clinic precisely matches each set using proprietary Data Match Technology. Every injector is individually serial numbered, with detailed flow matching and latency results supplied on the Data Match Sheet. The injectors are flow tested and rated at 43.5 PSI / 3 Bar and 90 degrees F fuel temperature using CF-16B calibration fluid.
Why Buy from Beefcake Racing?
Beefcake Racing specializes in Ford performance and high-performance fuel-system upgrades for everything from street-driven trucks to serious high-horsepower builds. Choosing the correct injector size and supporting fuel-system components is critical to reliable fuel delivery, accurate tuning, and strong drivability. Our experienced team can help you select the right components for your Raptor's engine combination and performance goals.
Questions about Fuel Injector Clinic part number is408-0775h or your Ford Raptor fuel system? Email Beefcake Racing at sales@beefcakeracing.com or call 1-855-827-7223.
CA Residents: WARNING: Cancer and Reproductive Harm www.P65Warnings.ca.gov
