Fuel Injector Clinic 2150cc High-Z Injector Set (is407-2150h) - 2021-2026 F-150 5.0L with Whipple
Feed a serious Whipple-supercharged 2021-2026 Ford F-150 5.0L with the massive fuel capacity of the Fuel Injector Clinic 2150cc High-Z injector set. This matched set of eight injectors is rated at 240 lbs/hr at 58 PSI fuel pressure and 2150cc/min, or 200 lbs/hr, at 43.5 PSI. Built for high-horsepower combinations with extreme fuel demands, the is407-2150h delivers tremendous flow while maintaining the short pulse width control and linearity needed for precise tuning, responsive low-speed operation, and strong drivability.
Because controlling an injector this large requires exceptional consistency, Fuel Injector Clinic uses its proprietary Data Match Technology dynamic flow matching process during production. Each injector is individually serial numbered, with detailed flow matching and latency information supplied on the Data Match Sheet. The set includes PGTDEN8 solder-in pigtails for the required connector conversion, while optional PADPDtoU8 plug-and-play adapters provide an installation option without cutting or soldering the factory wiring harness. Plug-and-play Ford ECU data is also available from Fuel Injector Clinic to support accurate calibration.
Specifications
- Part Number: is407-2150h
- Application: 2021-2026 Ford F-150 5.0L with Whipple
- Injector Quantity: 8
- Injector Flow Rate: 2150cc/min
- Flow Rate at 58 PSI: 240 lbs/hr
- Flow Rate at 43.5 PSI: 200 lbs/hr
- Impedance: High impedance / saturated
- Injector Design: Ball and seat
- Included Connector Solution: PGTDEN8 solder-in pigtails
- Optional Connector Solution: PADPDtoU8 plug-and-play adapters
- Injector Matching: Fuel Injector Clinic Data Match Technology dynamic flow matching
- Calibration Fluid: CF-16B
- FIC Test Pressure: 43.5 PSI / 3 Bar
- Test Fuel Temperature: 90 degrees F
- ECU Data: Plug-and-play Ford ECU data available from Fuel Injector Clinic
- O-Rings: Includes O-rings required for the applicable factory configuration
- Fuel Restriction: Do not use with Q16, VP Import, or other MTBE oxygenated fuels
- Alcohol Fuel Care: Follow Fuel Injector Clinic care instructions when using E85 or other alcohol-based fuels, particularly during prolonged periods of disuse
- Warranty: Lifetime warranty against failure caused by defects in original manufacture
Features
- Eight 2150cc/min High-Z performance fuel injectors
- 240 lbs/hr flow rating at 58 PSI fuel pressure
- 200 lbs/hr flow rating at 43.5 PSI / 3 Bar
- Built for extreme high-horsepower fuel demands
- High-impedance saturated ball and seat injector design
- Excellent linearity for a massive high-flow injector
- Superior short pulse width control and repeatability
- Dynamic flow matched using Fuel Injector Clinic Data Match Technology
- Improved ECU control in the sub 2ms pulse width range typical of idle and part-throttle operation
- Each injector is individually serial numbered
- Detailed Data Match Sheet provides flow matching and latency information
- Flow tested at 43.5 PSI / 3 Bar and 90 degrees F using CF-16B calibration fluid
- Includes PGTDEN8 solder-in pigtails for the required connector conversion
- Optional PADPDtoU8 plug-and-play adapters eliminate the need to cut or solder the factory wiring harness
- Plug-and-play Ford ECU calibration data available from Fuel Injector Clinic
- Includes O-rings required for the applicable factory configuration
- Uses brand-new injectors rather than remanufactured or core-program injectors
- Backed by Fuel Injector Clinic's lifetime warranty against manufacturing defects
Massive Fuel Capacity for Whipple F-150 Builds
A high-output Whipple-supercharged 5.0L can demand an enormous amount of fuel, and the is407-2150h is built for combinations where smaller injectors have become the limiting factor. Rated at 240 lbs/hr at 58 PSI, these injectors provide the fuel capacity required for extremely demanding performance builds while retaining the control necessary for accurate calibration. For F-150 owners pushing well beyond ordinary bolt-on power levels, the 2150cc injector provides substantial fueling headroom for the build.
Exceptional Short Pulse Width Control
Massive flow capacity is only useful if the ECU can accurately control it. Fuel Injector Clinic developed the 2150cc injector to maintain excellent low-end throttle response and short pulse width control despite its enormous size. Dynamic flow matching significantly improves ECU control in the sub 2ms pulse width range commonly encountered during idle and part-throttle operation, helping a properly calibrated high-horsepower truck retain the drivability expected from a street-driven combination.
Data Match Technology for Precise Tuning
Injector consistency becomes increasingly important as fuel flow and horsepower rise. Fuel Injector Clinic uses its proprietary Data Match Technology dynamic flow matching process during production of the 2150cc sets specifically because of their high flow rate. Every injector is individually serial numbered, and detailed flow matching and latency results are supplied on the Data Match Sheet. This gives your tuner the information needed for consistent cylinder-to-cylinder fuel delivery and precise calibration throughout the operating range.
Important Fuel Compatibility Warning
Do not use the is407-2150h with Q16, VP Import, or other MTBE oxygenated fuels. The internal construction of the 2150cc injector contains a seal that has been found to swell when exposed to MTBE. This swelling can significantly reduce injector flow, making the injector unsuitable for MTBE oxygenated fuels.
The 2150cc injector can be used with alcohol-based fuels such as E85, but proper care is important. Fuel Injector Clinic warns of potential corrosion issues resulting from prolonged disuse while the injectors remain exposed to alcohol-based fuels. Follow FIC's injector care recommendations when running E85 or similar fuels, especially before the truck will be stored or left unused for an extended period.
Connector Options
The is407-2150h requires an injector connector conversion for the listed application. Fuel Injector Clinic includes PGTDEN8 solder-in pigtails, allowing the injector connections on the wiring harness to be converted. Optional PADPDtoU8 plug-and-play adapters are available for owners who prefer installation without cutting or soldering the factory wiring harness. Fuel Injector Clinic uses brand-new, unused injectors for its performance applications rather than relying on remanufactured or core-program injectors.
Fitment
- 2021 Ford F-150 5.0L with Whipple
- 2022 Ford F-150 5.0L with Whipple
- 2023 Ford F-150 5.0L with Whipple
- 2024 Ford F-150 5.0L with Whipple
- 2025 Ford F-150 5.0L with Whipple
- 2026 Ford F-150 5.0L with Whipple
Fitment Note: This listing is intended for the title-listed 2021-2026 Ford F-150 5.0L applications equipped with a Whipple supercharger. If your truck uses a different supercharger, aftermarket fuel rail, or another non-standard fuel-system configuration, contact Beefcake Racing before ordering to verify compatibility.
FAQs
Why is the FIC is407-2150h listed at both 240 lbs/hr and 200 lbs/hr?
The ratings are measured at different fuel pressures. The is407-2150h is rated at 240 lbs/hr at 58 PSI fuel pressure and 200 lbs/hr at 43.5 PSI / 3 Bar. Injector flow increases as differential fuel pressure increases, so both specifications describe the same 2150cc injector under different pressure conditions.
Can the FIC is407-2150h be used with Q16 or VP Import?
No. Do not use these injectors with Q16, VP Import, or other MTBE oxygenated fuels. MTBE can cause an internal seal to swell and significantly reduce injector flow. E85 and other alcohol-based fuels require proper injector care, particularly when the vehicle will sit unused for an extended period.
Why Buy from Beefcake Racing?
Beefcake Racing specializes in Ford performance, Whipple supercharger combinations, and high-horsepower fuel-system upgrades. When your F-150 build requires an injector as large as 2150cc, matching the injectors, fuel choice, tuning requirements, and supporting fuel system correctly is critical. Our experienced team can help you select the components needed to support your combination and performance goals.
Questions about Fuel Injector Clinic part number is407-2150h or your Whipple F-150 fuel system? Email Beefcake Racing at sales@beefcakeracing.com or call 1-855-827-7223.
CA Residents: WARNING: Cancer and Reproductive Harm www.P65Warnings.ca.gov
