Fuel Injector Clinic 2150cc High-Z Injector Set (is406-2150h) - 1985-2003 Ford F-150 / 1993-1995 Lightning
Feed a serious high-horsepower Ford truck build with the Fuel Injector Clinic 2150cc High-Z injector set for 1985-2003 Ford F-150 and 1993-1995 Ford Lightning applications. This matched set of eight massive 2150cc/min injectors flows 200 lbs/hr at 43.5 PSI fuel pressure, delivering the fuel capacity required by demanding performance combinations without abandoning the low-pulse-width control needed for drivability. FIC's advanced injector technology, excellent linearity, and dynamic flow matching make the is406-2150h an outstanding choice when your combination demands extreme fuel volume along with precise ECU control.
The is406-2150h is precisely matched using Fuel Injector Clinic's proprietary Data Match Technology, with dynamic flow matching used to improve injector control in the sub-2ms pulse width range commonly encountered during idle and part-throttle operation. Every injector is individually serial numbered, and detailed flow matching and latency results are supplied on the Data Match Sheet. FIC flow tests and rates these injectors at 43.5 PSI / 3 Bar and 90 degrees F fuel temperature using CF-16B calibration fluid. PGTDEN8 solder-in pigtails are included, while optional PADPDtoJ8 plug-and-play adapters provide installation without cutting or soldering the factory harness.
Specifications
- Part Number: is406-2150h
- Injector Quantity: 8
- Flow Rate: 2150cc/min
- Flow Rate at 43.5 PSI: 200 lbs/hr
- Fuel Pressure Rating: 43.5 PSI / 3 Bar
- Impedance: High impedance / saturated
- Injector Design: Ball and seat
- Included Connector Solution: PGTDEN8 solder-in pigtails
- Optional Connector Solution: PADPDtoJ8 plug-and-play adapters
- Injector Matching: Fuel Injector Clinic Data Match Technology with dynamic flow matching
- Calibration Fluid: CF-16B
- Test Fuel Temperature: 90 degrees F
- ECU Data: Plug-and-play Ford ECU data available from Fuel Injector Clinic
- O-Rings: Includes O-rings required for the applicable factory configuration
- MTBE Fuel Compatibility: Not compatible with VP Import, Q16, or other MTBE-oxygenated fuels
- Warranty: Lifetime warranty against failure caused by defects in original manufacture
Features
- Eight massive 2150cc/min High-Z performance fuel injectors
- 200 lbs/hr flow rating at 43.5 PSI fuel pressure
- High-impedance saturated ball and seat injector design
- Exceptional fuel capacity for demanding high-horsepower combinations
- Excellent linearity throughout the injector operating range
- Advanced short pulse width control for improved low-speed behavior
- Dynamic flow matched using Fuel Injector Clinic Data Match Technology
- Improved ECU control in the sub-2ms pulse width range
- Each injector is individually serial numbered
- Data Match Sheet provides detailed flow matching and latency information
- Flow tested and rated at 43.5 PSI / 3 Bar
- Tested at 90 degrees F fuel temperature using CF-16B calibration fluid
- Includes PGTDEN8 solder-in pigtails for injector plug conversion
- Optional PADPDtoJ8 plug-and-play adapters eliminate cutting or soldering the factory harness
- Plug-and-play Ford ECU calibration data available from Fuel Injector Clinic
- Includes O-rings required for the applicable factory configuration
- Uses brand-new injectors rather than remanufactured or core-program injectors
- Backed by Fuel Injector Clinic's lifetime warranty against manufacturing defects
Massive 2150cc Fuel Capacity with Precise Low-Speed Control
Injectors capable of supporting extreme fuel demand also need to remain controllable when the engine requires only a small amount of fuel. That balance is where the FIC 2150cc injector stands apart. Fuel Injector Clinic uses dynamic flow matching during production to improve ECU control in the sub-2ms pulse width range typically encountered during idle and part-throttle operation. The result is an injector designed to combine massive 2150cc/min capacity with the precise short pulse width behavior required for a properly calibrated performance engine.
Data Match Technology for Serious Tuning
At this level of fuel delivery, injector consistency becomes especially important. Fuel Injector Clinic precisely matches each is406-2150h set using proprietary Data Match Technology. Every injector is individually serial numbered, and detailed flow matching and latency information is supplied on the Data Match Sheet. This provides the tuner with accurate injector-specific information to help achieve consistent cylinder-to-cylinder fueling across the operating range.
Important Fuel Compatibility Warning
DO NOT use the is406-2150h with VP Import, Q16, or other MTBE-oxygenated fuels. The internal construction of the 2150cc injector contains a seal that can swell when exposed to MTBE. This swelling can significantly reduce injector flow, making the injector unsuitable for MTBE-oxygenated fuels.
Care instructions are also important when these injectors are used with alcohol-based fuels such as E85. Prolonged disuse while alcohol-based fuel remains in the injectors can create potential corrosion issues. Follow Fuel Injector Clinic's injector care recommendations when storing or operating a vehicle on alcohol-based fuels.
Connector Options for Installation
The is406-2150h requires an injector connector conversion for the listed applications. Fuel Injector Clinic includes PGTDEN8 solder-in pigtails, allowing the original injector connectors on the wiring harness to be replaced. Optional PADPDtoJ8 plug-and-play adapters provide an alternative for owners who want to connect the injectors without cutting or soldering the factory wiring harness.
Fuel Injector Clinic uses brand-new, unused injectors for its performance applications rather than relying on remanufactured or core-program injectors. This avoids introducing the additional uncertainty associated with previously used injector components into a high-performance fuel system.
Fitment
- 1985 Ford F-150
- 1986 Ford F-150
- 1987 Ford F-150
- 1988 Ford F-150
- 1989 Ford F-150
- 1990 Ford F-150
- 1991 Ford F-150
- 1992 Ford F-150
- 1993 Ford F-150
- 1994 Ford F-150
- 1995 Ford F-150
- 1996 Ford F-150
- 1997 Ford F-150
- 1998 Ford F-150
- 1999 Ford F-150
- 2000 Ford F-150
- 2001 Ford F-150
- 2002 Ford F-150
- 2003 Ford F-150
- 1993 Ford F-150 Lightning
- 1994 Ford F-150 Lightning
- 1995 Ford F-150 Lightning
Fitment Note: This listing is intended for the title-listed 1985-2003 Ford F-150 and 1993-1995 Ford Lightning applications. If your truck uses aftermarket fuel rails or another non-standard fuel-system configuration, contact Beefcake Racing before ordering to verify proper injector fitment.
FAQs
Can FIC is406-2150h injectors be used with Q16 or VP Import fuel?
No. Do not use these 2150cc injectors with Q16, VP Import, or other MTBE-oxygenated fuels. MTBE can cause an internal seal to swell, significantly reducing injector flow. Alcohol-based fuels such as E85 also require proper injector care during periods of disuse.
Does the Fuel Injector Clinic is406-2150h require an injector plug conversion?
Yes. PGTDEN8 solder-in pigtails are included for converting the wiring harness. Optional PADPDtoJ8 plug-and-play adapters are available for installation without cutting or soldering the factory harness.
Why Buy from Beefcake Racing?
Beefcake Racing specializes in Ford performance and high-performance fuel-system upgrades for everything from classic F-150 builds to first-generation Ford Lightning combinations. When your build reaches the point where 2150cc injectors are required, choosing the correct supporting fuel-system components and calibration strategy matters. Our experienced team can help you match your injectors and supporting components to your engine setup, fuel choice, and performance goals.
Questions about Fuel Injector Clinic part number is406-2150h or your Ford truck fuel system? Email Beefcake Racing at sales@beefcakeracing.com or call 1-855-827-7223.
CA Residents: WARNING: Cancer and Reproductive Harm www.P65Warnings.ca.gov
