Fuel Injector Clinic 1200cc High-Z Injector Set (is406-1200h) - 1985-2003 Ford F-150 / 1993-1995 Lightning
Upgrade the fuel system in your 1985-2003 Ford F-150 or 1993-1995 Ford Lightning with the Fuel Injector Clinic 1200cc High-Z injector set. This matched set of eight injectors flows 1200cc/min, or 110 lbs/hr, at 43.5 PSI fuel pressure, providing serious fuel capacity for modified and high-performance Ford truck combinations while retaining the precise control needed for strong drivability. Excellent linearity and short pulse width repeatability help deliver predictable fueling from idle and part throttle through higher-load operation, while drop-in sizing and plug compatibility make installation straightforward.
Every is406-1200h set is precisely matched using Fuel Injector Clinic's proprietary Data Match Technology. Each injector is individually serial numbered, with detailed flow matching and latency results supplied on the Data Match Sheet to provide accurate information for calibration. FIC flow tests and rates these injectors at 43.5 PSI / 3 Bar and 90 degrees F fuel temperature using CF-16B calibration fluid. Plug-and-play Ford ECU data is also available from Fuel Injector Clinic, and all O-rings required for the applicable factory configuration are included. The is406-1200h is the current replacement for the previous is406-1100h.
Specifications
- Part Number: is406-1200h
- Previous Part Number: is406-1100h
- Injector Quantity: 8
- Flow Rate: 1200cc/min
- Flow Rate at 43.5 PSI: 110 lbs/hr
- Fuel Pressure Rating: 43.5 PSI / 3 Bar
- Impedance: High impedance / saturated
- Injector Design: Ball and seat
- Fitment Type: Drop-in for size and plug
- Injector Matching: Fuel Injector Clinic Data Match Technology
- Calibration Fluid: CF-16B
- Test Fuel Temperature: 90 degrees F
- ECU Data: Plug-and-play Ford ECU data available from Fuel Injector Clinic
- O-Rings: Includes O-rings required for the applicable factory configuration
- Warranty: Lifetime warranty against failure caused by defects in original manufacture
Features
- Eight 1200cc/min High-Z performance fuel injectors
- 110 lbs/hr flow rating at 43.5 PSI fuel pressure
- High-impedance saturated ball and seat injector design
- Serious fuel capacity for modified and high-performance Ford truck combinations
- Excellent linearity throughout the injector operating range
- Superior short pulse width control and repeatability
- Drop-in sizing and plug compatibility
- No injector plug conversion required
- Precisely matched using Fuel Injector Clinic Data Match Technology
- Each injector is individually serial numbered
- Data Match Sheet provides detailed flow matching and latency information
- Flow tested and rated at 43.5 PSI / 3 Bar
- Tested at 90 degrees F fuel temperature using CF-16B calibration fluid
- Plug-and-play Ford ECU calibration data available from Fuel Injector Clinic
- Includes O-rings required for the applicable factory configuration
- Current replacement for previous FIC part number is406-1100h
- Backed by Fuel Injector Clinic's lifetime warranty against manufacturing defects
1200cc Fuel Capacity with Precise Control
As airflow and horsepower increase, the fuel system needs enough injector capacity to keep pace without compromising low-speed control. The FIC 1200cc injector combines 1200cc/min of flow with excellent linearity and short pulse width repeatability, giving performance Ford truck builds substantial fuel delivery capability while retaining the accurate injector behavior needed during idle, cruising, and part-throttle operation.
Data Match Technology for Accurate Tuning
Consistent injector performance across all eight cylinders is essential to a properly calibrated performance engine. Fuel Injector Clinic precisely matches each is406-1200h set using proprietary Data Match Technology. Every injector is individually serial numbered, and detailed flow matching and latency results are supplied on the Data Match Sheet. This gives your tuner accurate injector-specific information for consistent cylinder-to-cylinder fueling and precise calibration throughout the operating range.
Built for Tunability and Drivability
Fuel Injector Clinic combines substantial flow capacity with superior short pulse width control and state-of-the-art injector matching. These characteristics help the ECU accurately meter fuel when demand is low while providing the additional volume required as engine load increases. The result is an injector designed to deliver both high-performance fueling capability and the predictable behavior needed for a properly tuned street-driven truck.
Drop-In Size and Plug
The is406-1200h is designed as a drop-in solution for size and plug in the applicable factory configuration. No injector plug conversion is required, eliminating the need for solder-in pigtails or electrical adapters. Fuel Injector Clinic also supplies the necessary O-rings for the factory application, while available plug-and-play Ford ECU data helps provide tuners with the information needed for calibration.
Fitment
- 1985 Ford F-150
- 1986 Ford F-150
- 1987 Ford F-150
- 1988 Ford F-150
- 1989 Ford F-150
- 1990 Ford F-150
- 1991 Ford F-150
- 1992 Ford F-150
- 1993 Ford F-150
- 1994 Ford F-150
- 1995 Ford F-150
- 1996 Ford F-150
- 1997 Ford F-150
- 1998 Ford F-150
- 1999 Ford F-150
- 2000 Ford F-150
- 2001 Ford F-150
- 2002 Ford F-150
- 2003 Ford F-150
- 1993 Ford F-150 Lightning
- 1994 Ford F-150 Lightning
- 1995 Ford F-150 Lightning
Fitment Note: This listing is intended for the title-listed 1985-2003 Ford F-150 and 1993-1995 Ford Lightning applications. If your truck uses aftermarket fuel rails or another non-standard fuel-system configuration, contact Beefcake Racing before ordering to verify proper injector fitment.
FAQs
Does the Fuel Injector Clinic is406-1200h require an injector plug conversion?
No. Fuel Injector Clinic specifies the is406-1200h as drop-in for size and plug, so an injector plug conversion is not required for the applicable factory configuration.
Is is406-1200h the replacement for the older is406-1100h injector set?
Yes. Fuel Injector Clinic identifies is406-1200h as the current 1200cc injector set and specifically notes that it was previously sold under part number is406-1100h.
Why Buy from Beefcake Racing?
Beefcake Racing specializes in Ford performance and high-performance fuel-system upgrades for everything from classic F-150 builds to first-generation Ford Lightning combinations. Whether you are upgrading a street-driven truck or building a higher-horsepower combination, our experienced team can help you select injectors and supporting fuel-system components that match your engine setup and performance goals.
Questions about Fuel Injector Clinic part number is406-1200h or your Ford truck fuel system? Email Beefcake Racing at sales@beefcakeracing.com or call 1-855-827-7223.
CA Residents: WARNING: Cancer and Reproductive Harm www.P65Warnings.ca.gov
