Fuel Injector Clinic 1000cc High-Z Injector Set (is406-1000h) - 1985-2003 Ford F-150 / 1993-1995 Lightning
Step up the fuel delivery on your 1985-2003 Ford F-150 or 1993-1995 Ford Lightning with the Fuel Injector Clinic 1000cc High-Z injector set. This matched set of eight injectors flows 1000cc/min, or 95 lbs/hr, at 43.5 PSI fuel pressure, providing substantial fuel capacity for modified and high-performance Ford truck combinations. Excellent linearity and short pulse width repeatability help maintain precise fuel control from idle and part throttle through higher-load operation, giving your tuner the consistency needed to build a responsive, well-calibrated combination.
Every is406-1000h set is precisely matched using Fuel Injector Clinic's proprietary Data Match Technology. Each injector is individually serial numbered, with detailed flow matching and latency results supplied on the Data Match Sheet. FIC flow tests and rates these injectors at 43.5 PSI / 3 Bar and 90 degrees F fuel temperature using CF-16B calibration fluid. PGTUSC8 solder-in pigtails are available for the required injector plug conversion, while PADPUtoJ8 plug-and-play adapters provide an alternative that eliminates cutting or soldering the factory harness. Plug-and-play Ford ECU data is also available from Fuel Injector Clinic to support accurate calibration.
Specifications
- Part Number: is406-1000h
- Injector Quantity: 8
- Flow Rate: 1000cc/min
- Flow Rate at 43.5 PSI: 95 lbs/hr
- Fuel Pressure Rating: 43.5 PSI / 3 Bar
- Impedance: High impedance / saturated
- Injector Design: Ball and seat
- Connector Option: PGTUSC8 solder-in pigtails
- Optional Connector Solution: PADPUtoJ8 plug-and-play adapters
- Injector Matching: Fuel Injector Clinic Data Match Technology
- Calibration Fluid: CF-16B
- Test Fuel Temperature: 90 degrees F
- ECU Data: Plug-and-play Ford ECU data available from Fuel Injector Clinic
- O-Rings: Includes O-rings required for the applicable factory configuration
- Warranty: Lifetime warranty against failure caused by defects in original manufacture
Features
- Eight 1000cc/min High-Z performance fuel injectors
- 95 lbs/hr flow rating at 43.5 PSI fuel pressure
- High-impedance saturated ball and seat injector design
- Substantial fuel capacity for modified and high-performance Ford truck combinations
- Excellent linearity throughout the injector operating range
- Superior short pulse width control and repeatability
- Precisely matched using Fuel Injector Clinic Data Match Technology
- Each injector is individually serial numbered
- Data Match Sheet provides detailed flow matching and latency information
- Flow tested and rated at 43.5 PSI / 3 Bar
- Tested at 90 degrees F fuel temperature using CF-16B calibration fluid
- PGTUSC8 solder-in pigtail connector option
- Optional PADPUtoJ8 plug-and-play adapters eliminate cutting or soldering the factory harness
- Plug-and-play Ford ECU calibration data available from Fuel Injector Clinic
- Includes O-rings required for the applicable factory configuration
- Uses brand-new injectors rather than remanufactured or core-program injectors
- Backed by Fuel Injector Clinic's lifetime warranty against manufacturing defects
1000cc Fuel Capacity for High-Performance Ford Trucks
As airflow, boost, and horsepower increase, the factory fuel system can quickly become a limiting factor. The FIC 1000cc injector provides the additional fuel capacity required by serious performance combinations while retaining the accurate low-pulse-width behavior needed for proper calibration. With 1000cc/min of flow available, the is406-1000h gives modified F-150 and first-generation Lightning builds substantial fueling capability while keeping precise injector control a priority.
Data Match Technology for Precise Tuning
Injector consistency matters across the entire operating range, especially as fuel demand increases. Fuel Injector Clinic precisely matches each is406-1000h set using proprietary Data Match Technology. Every injector is individually serial numbered, and detailed flow matching and latency information is supplied on the Data Match Sheet. This gives your tuner accurate injector-specific information for consistent cylinder-to-cylinder fueling and precise calibration.
High Flow with Street-Friendly Control
A performance injector needs to accurately meter small quantities of fuel during idle and cruising while supplying significantly greater fuel volume as engine load increases. Fuel Injector Clinic combines 1000cc/min capacity with excellent linearity and superior short pulse width control, helping the ECU accurately manage fuel delivery across a wide operating range. That balance makes the is406-1000h a strong option for performance Ford trucks where both fuel capacity and drivability matter.
Connector Options for Installation
The is406-1000h uses a connector configuration that requires adaptation to the factory wiring harness. Fuel Injector Clinic offers PGTUSC8 solder-in pigtails that replace the existing injector plugs. For owners who prefer not to cut or solder the factory harness, optional PADPUtoJ8 plug-and-play adapters connect the injectors to the existing harness.
Fuel Injector Clinic uses brand-new, unused injectors for its performance applications rather than relying on remanufactured or core-program injectors. This avoids introducing the additional uncertainty associated with previously used injector components into a performance fuel system.
Fitment
- 1985 Ford F-150
- 1986 Ford F-150
- 1987 Ford F-150
- 1988 Ford F-150
- 1989 Ford F-150
- 1990 Ford F-150
- 1991 Ford F-150
- 1992 Ford F-150
- 1993 Ford F-150
- 1994 Ford F-150
- 1995 Ford F-150
- 1996 Ford F-150
- 1997 Ford F-150
- 1998 Ford F-150
- 1999 Ford F-150
- 2000 Ford F-150
- 2001 Ford F-150
- 2002 Ford F-150
- 2003 Ford F-150
- 1993 Ford F-150 Lightning
- 1994 Ford F-150 Lightning
- 1995 Ford F-150 Lightning
Fitment Note: This listing is intended for the title-listed 1985-2003 Ford F-150 and 1993-1995 Ford Lightning applications. If your truck uses aftermarket fuel rails or another non-standard fuel-system configuration, contact Beefcake Racing before ordering to verify proper injector fitment.
FAQs
Does the Fuel Injector Clinic is406-1000h require an injector plug conversion?
Yes. Fuel Injector Clinic offers PGTUSC8 solder-in pigtails for converting the wiring harness to the injector connectors. Optional PADPUtoJ8 plug-and-play adapters are available for installation without cutting or soldering the factory harness.
How are the FIC is406-1000h 1000cc injectors matched?
Fuel Injector Clinic precisely matches the set using its proprietary Data Match Technology. Each injector is individually serial numbered, with detailed flow matching and latency results supplied on the Data Match Sheet to provide accurate injector information for tuning.
Why Buy from Beefcake Racing?
Beefcake Racing specializes in Ford performance and high-performance fuel-system upgrades for everything from classic F-150 builds to first-generation Ford Lightning combinations. Whether you are upgrading a street-driven truck or putting together a serious high-horsepower build, our experienced team can help you select injectors and supporting fuel-system components that match your engine setup and performance goals.
Questions about Fuel Injector Clinic part number is406-1000h or your Ford truck fuel system? Email Beefcake Racing at sales@beefcakeracing.com or call 1-855-827-7223.
CA Residents: WARNING: Cancer and Reproductive Harm www.P65Warnings.ca.gov
