Fuel Injector Clinic 2150cc High-Z Fuel Injector Set (IS156-2150H) - 2008-2013 Dodge 4.7L / 2003-Present 5.7L
Feed a serious high-horsepower Dodge build with the massive fuel capacity and precise low-pulse-width control of the Fuel Injector Clinic IS156-2150H 2150cc High-Z Fuel Injector Set. This complete eight-injector set flows 2150cc/min, or 200 lbs/hr, at 43.5 psi (3 Bar) and an impressive 2500cc/min, or 240 lbs/hr, at the Dodge OE fuel pressure of 58 psi (4 Bar). Despite that enormous flow capability, FIC engineered the 2150cc injector around excellent low-end throttle response and short pulse width control, giving tuners the precision needed to manage a fuel injector of this size during idle and part-throttle operation.
Fuel Injector Clinic uses its proprietary Data Match Technology with dynamic flow matching during production of the IS156-2150H. This process is especially important with an injector of this flow capacity because it improves the ECU's ability to control fueling in the sub-2ms pulse width range commonly encountered during idle and part-throttle conditions. Each injector is individually serial numbered, with detailed flow matching and latency information supplied on the included Data Match Sheet. The set includes PGTDEN8 solder-in pigtails, while optional PADPDtoU8 plug-and-play adapters provide an installation option that does not require cutting or soldering the factory wiring harness.
Specifications
- Manufacturer: Fuel Injector Clinic
- Part Number: IS156-2150H
- Injector Quantity: Set of 8
- Flow at 43.5 psi (3 Bar): 2150cc/min / 200 lbs/hr
- Flow at OE 58 psi (4 Bar): 2500cc/min / 240 lbs/hr
- Impedance: High impedance / High-Z
- Injector Type: Saturated
- Matching: Fuel Injector Clinic Data Match Technology with dynamic flow matching
- Included Pigtails: PGTDEN8
- Optional Plug-and-Play Adapters: PADPDtoU8
- Plug Conversion Required: Yes, using included solder-in pigtails or optional plug-and-play adapters
- Flow Test Pressure: 43.5 psi (3 Bar)
- Flow Test Fuel Temperature: 90 degrees F
- ECU Data: Plug-and-play Dodge ECU data available from Fuel Injector Clinic
- O-Rings: Includes O-rings required for the listed factory applications
- MTBE Fuel Compatibility: Do not use with Q16, VP Import, or other MTBE oxygenated fuels
- Alcohol-Based Fuel Care: Follow FIC care instructions when using E85 or other alcohol-based fuels, particularly before prolonged periods of disuse
- Warranty: Lifetime warranty against failure caused by defects in original manufacture
Features
- Complete set of eight massive 2150cc high-impedance fuel injectors
- 2150cc/min and 200 lbs/hr flow rating at 43.5 psi (3 Bar)
- 2500cc/min and 240 lbs/hr flow at Dodge OE 58 psi (4 Bar) fuel pressure
- Saturated, High-Z injector design
- Engineered for extreme fuel-flow requirements
- Excellent low-end throttle response for an injector of this capacity
- Superior short pulse width control
- Dynamic flow matching improves ECU control in the sub-2ms pulse width range
- Precisely matched using Fuel Injector Clinic proprietary Data Match Technology
- Each injector is individually serial numbered
- Includes a detailed Data Match Sheet with flow matching and latency information
- Flow tested at 43.5 psi (3 Bar) and 90 degrees F using calibration fluid
- Includes PGTDEN8 solder-in pigtails
- Optional PADPDtoU8 plug-and-play adapters available for installation without cutting or soldering
- Plug-and-play Dodge ECU data available from Fuel Injector Clinic
- Includes O-rings required for the listed factory applications
- Backed by Fuel Injector Clinic's lifetime warranty against manufacturing defects
2150cc Rated Flow and 240 lbs/hr at OE Fuel Pressure
The IS156-2150H is built for Dodge combinations with serious fuel demands. Fuel Injector Clinic rates these injectors at 2150cc/min, or 200 lbs/hr, at its standard 43.5 psi (3 Bar) test pressure. At the Dodge OE fuel pressure of 58 psi (4 Bar), available flow increases to 2500cc/min, or 240 lbs/hr. Because injector flow changes with fuel pressure, both figures matter when sizing the injectors and supporting fuel system for the engine's horsepower, fuel type, and intended operating conditions.
Dynamic Data Match Technology
Managing an injector with this much flow requires more than raw capacity. Fuel Injector Clinic uses state-of-the-art Data Match Technology with dynamic flow matching during production of its 2150cc injector sets. The process is designed to improve ECU control in the sub-2ms pulse width range typically encountered during idle and part-throttle operation. Each injector is individually serial numbered, and its results are supplied on the included Data Match Sheet with detailed flow matching and latency information for calibration.
Massive Flow with Short Pulse Width Control
The standout characteristic of the FIC 2150cc is its ability to combine extreme fuel capacity with the low-pulse-width control needed outside of wide-open throttle. Superior short pulse width behavior gives the ECU greater control when only a small amount of fuel is required, helping make an injector of this size more manageable during idle and part-throttle conditions. For extreme-power applications, that balance between maximum flow and controllability is just as important as the injector's headline 2150cc rating.
Important MTBE Fuel Compatibility Warning
Do not use the IS156-2150H with VP Import, Q16, or other MTBE oxygenated fuels. The internal construction of the FIC 2150cc injector contains a seal that has been found to swell when exposed to MTBE. This swelling can significantly reduce injector flow, making the injector unsuitable for these fuels. This restriction is specific and important when selecting fuel for an engine equipped with FIC 2150cc injectors.
E85 and Alcohol-Based Fuel Care
The IS156-2150H may be used in alcohol-based fuel applications such as E85, but Fuel Injector Clinic's care instructions should be followed. Prolonged disuse while alcohol-based fuel remains in the injectors can create potential corrosion concerns. For vehicles that may sit for extended periods, proper fuel system maintenance and storage procedures are especially important.
Pigtails and Plug-and-Play Adapter Options
The IS156-2150H requires an electrical connector conversion in the listed applications. PGTDEN8 solder-in pigtails are included and can be installed in place of the existing injector connectors. For owners who do not want to cut or solder the factory wiring harness, optional PADPDtoU8 plug-and-play adapters convert the injector connection to the factory harness connection. Fuel Injector Clinic uses this configuration so it can supply brand-new, unused performance injectors rather than relying on remanufactured or core-program injectors.
Fitment
- 2008 Dodge 4.7L
- 2009 Dodge 4.7L
- 2010 Dodge 4.7L
- 2011 Dodge 4.7L
- 2012 Dodge 4.7L
- 2013 Dodge 4.7L
- 2003 Dodge 5.7L
- 2004 Dodge 5.7L
- 2005 Dodge 5.7L
- 2006 Dodge 5.7L
- 2007 Dodge 5.7L
- 2008 Dodge 5.7L
- 2009 Dodge 5.7L
- 2010 Dodge 5.7L
- 2011 Dodge 5.7L
- 2012 Dodge 5.7L
- 2013 Dodge 5.7L
- 2014 Dodge 5.7L
- 2015 Dodge 5.7L
- 2016 Dodge 5.7L
- 2017 Dodge 5.7L
- 2018 Dodge 5.7L
- 2019 Dodge 5.7L
- 2020 Dodge 5.7L
- 2021 Dodge 5.7L
- 2022 Dodge 5.7L
- 2023 Dodge 5.7L
- 2024 Dodge 5.7L
- 2025 Dodge 5.7L
- 2026 Dodge 5.7L
- Present Dodge 5.7L
FAQs
Can FIC IS156-2150H 2150cc injectors be used with Q16 or VP Import?
No. Fuel Injector Clinic specifically warns against using its 2150cc injectors with Q16, VP Import, or other MTBE oxygenated fuels. MTBE can cause an internal seal to swell, resulting in a significant reduction in injector flow.
Do the FIC IS156-2150H injectors require a connector conversion?
Yes. The set includes PGTDEN8 solder-in pigtails for the required connector conversion. Optional PADPDtoU8 plug-and-play adapters can be used instead if you want to install the injectors without cutting or soldering the factory wiring harness.
Build Your High-Horsepower Dodge Fuel System with Beefcake Racing
When your Dodge build requires 2150cc injectors, the rest of the fuel system and calibration need to be ready for the same level of performance. Beefcake Racing can help you select the right Fuel Injector Clinic injectors and supporting fuel system components for your combination. Call 1-855-827-7223 or email sales@beefcakeracing.com for expert assistance.
CA Residents: WARNING: Cancer and Reproductive Harm www.P65Warnings.ca.gov
