Fuel Injector Clinic 2150cc Fuel Injector Set - High Z (is140-2150h) - Scion tC / xB / Toyota 1ZZ
When your Scion or compatible Toyota build demands serious fuel volume, the Fuel Injector Clinic is140-2150h 2150cc High-Z fuel injector set delivers massive capacity without giving up the precise control needed at idle and part throttle. This complete set of four saturated, high-impedance injectors uses FIC's advanced Data Match Technology to help the ECU accurately control these large injectors even in the sub-2ms pulse width range. The result is a high-flow injector engineered for extreme performance applications while retaining the short pulse width control and drivability that matter on a properly tuned combination.
Each injector is individually serial numbered and supplied with a Data Match Sheet containing detailed flow matching and latency information. Fuel Injector Clinic flow tests and rates these injectors at 43.5 PSI (3 Bar) with fuel at 90 degrees F using CF-16B calibration fluid. PGTDEN4 solder-in pigtails are included, while optional PADPDtoT4 plug-and-play adapters allow connection to the applicable factory harness without cutting or soldering. These 2150cc injectors must not be used with VP Import, Q16, or other MTBE oxygenated fuels.
Specifications
- Manufacturer: Fuel Injector Clinic
- Part Number: is140-2150h
- Flow Rate: 2150cc/min
- Injector Quantity: 4
- Injector Type: Saturated / high impedance
- Impedance: High-Z / high impedance
- Matching Technology: Fuel Injector Clinic Data Match Technology
- Flow Test Pressure: 43.5 PSI (3 Bar)
- Flow Test Fuel Temperature: 90 degrees F
- Calibration Fluid: CF-16B
- Pigtails: PGTDEN4
- Optional Plug-and-Play Adapters: PADPDtoT4
- O-Rings: Included as required for the listed factory application
- MTBE Fuel Compatibility: Not compatible with VP Import, Q16, or other MTBE oxygenated fuels
- Warranty: Lifetime warranty against failure caused by defects in original manufacture
Features
- Complete set of four massive 2150cc/min performance fuel injectors
- Saturated, high-impedance design
- High fuel volume for extreme horsepower applications
- Advanced dynamic flow matching using Fuel Injector Clinic Data Match Technology
- Designed for improved ECU control in the sub-2ms pulse width range
- Excellent short pulse width control for such a high-flow injector
- Each injector is individually serial numbered
- Detailed Data Match Sheet provides flow matching and latency information
- Flow tested at 43.5 PSI (3 Bar) and 90 degrees F using CF-16B calibration fluid
- PGTDEN4 solder-in pigtails included
- Optional PADPDtoT4 plug-and-play adapters eliminate the need to cut or solder the applicable factory harness
- Brand-new injectors rather than remanufactured or core-program units
- Includes required O-rings for the listed factory application
- Lifetime warranty against failure caused by defects in original manufacture
Massive Fuel Capacity With Precise Low-Pulse Control
Moving to a 2150cc injector creates a unique tuning challenge because an injector capable of supplying enormous fuel volume must still respond accurately when the engine needs only a small amount of fuel. Fuel Injector Clinic addresses that challenge with dynamic Data Match Technology specifically designed to improve control of these large injectors in the sub-2ms pulse width range commonly encountered during idle and part-throttle operation.
This combination of massive flow capacity and carefully controlled injector behavior makes the is140-2150h a serious fueling solution for high-output builds that have moved well beyond the capacity of smaller injectors.
Data Match Technology
Fuel Injector Clinic uses its proprietary Data Match Technology during production of the is140-2150h set to precisely match injector performance. Each injector is individually serial numbered, and the supplied Data Match Sheet provides detailed flow matching and latency information. This injector-specific data gives tuners valuable information for accurately calibrating a high-performance fuel system and maintaining consistent fuel delivery across all four cylinders.
Important Fuel Compatibility Warning
Do not use these 2150cc injectors with VP Import, Q16, or other MTBE oxygenated fuels. The internal construction of the 2150cc injector contains a seal that can swell after contact with MTBE. This swelling can significantly reduce injector flow, making the injector unsuitable for MTBE oxygenated fuels.
When these injectors are used with alcohol-based fuels such as E85, Fuel Injector Clinic's care instructions should be followed. Prolonged periods of disuse while the injectors remain exposed to alcohol-based fuel can create potential corrosion concerns.
Wiring and Installation
The is140-2150h injector set requires an injector plug conversion when used with the applicable factory wiring harness. Included PGTDEN4 solder-in pigtails can be used to replace the existing injector plugs. Optional PADPDtoT4 plug-and-play adapters provide an alternative that connects the injectors without cutting or soldering the factory harness.
Fuel Injector Clinic uses brand-new, unused injectors for its performance applications rather than remanufactured or core-program injectors. The injectors are configured with the O-rings required for the listed factory application. If your vehicle uses an aftermarket fuel rail or another unusual fuel-system configuration, contact Beefcake Racing before ordering to verify proper fitment.
Fitment
- 2005 Scion tC
- 2006 Scion tC
- 2007 Scion tC
- 2008 Scion tC
- 2009 Scion tC
- 2010 Scion tC
- 2011 Scion tC
- 2012 Scion tC
- 2013 Scion tC
- 2014 Scion tC
- 2015 Scion tC
- 2016 Scion tC
- 2008 Scion xB
- 2009 Scion xB
- 2010 Scion xB
- 2011 Scion xB
- 2012 Scion xB
- 2013 Scion xB
- 2014 Scion xB
- 2015 Scion xB
- Select Toyota applications utilizing the 1ZZ engine
FAQs
Can Fuel Injector Clinic is140-2150h injectors be used with Q16 or VP Import?
No. These 2150cc injectors must not be used with Q16, VP Import, or other MTBE oxygenated fuels. MTBE can cause an internal seal to swell, resulting in a significant reduction in injector flow.
What wiring is required for the FIC is140-2150h injector set?
The injectors require a plug conversion when used with the applicable factory harness. PGTDEN4 solder-in pigtails are included, or optional PADPDtoT4 plug-and-play adapters can be used to connect the injectors without cutting or soldering the factory wiring harness.
Why Buy Fuel Injector Clinic Injectors From Beefcake Racing?
Beefcake Racing is your source for Fuel Injector Clinic injectors and the supporting fuel-system components required for serious high-horsepower builds. Whether you are upgrading a Scion tC, Scion xB, or compatible Toyota application, our team can help you select the injectors and supporting components appropriate for your combination and fuel choice. Questions about the Fuel Injector Clinic is140-2150h? Email sales@beefcakeracing.com or call 1-855-827-7223.
CA Residents: WARNING: Cancer and Reproductive Harm www.P65Warnings.ca.gov
