Fuel Injector Clinic 1000cc Fuel Injector Set - High Z (is140-1000h) - Scion tC / xB / Toyota 1ZZ
Upgrade the fuel system in your Scion or compatible Toyota application with the Fuel Injector Clinic is140-1000h 1000cc High-Z fuel injector set. This complete set of four saturated, high-impedance ball and seat injectors delivers the increased fuel capacity needed for modified and higher-horsepower combinations while maintaining the linearity, short pulse width control, and repeatability required for precise tuning and strong drivability. Fuel Injector Clinic combines modern injector technology with its proprietary Data Match Technology to provide consistent fuel delivery across the complete matched set.
Each injector is individually serial numbered, with detailed results supplied on the included Data Match Sheet for valuable flow matching and latency information. FIC rates and flow tests these injectors at 43.5 PSI (3 Bar) with fuel at 90 degrees F using CF-16B calibration fluid. The set uses PGTUSC4 solder-in pigtails, while optional PADPUtoT4 plug-and-play adapters provide an installation option that does not require cutting or soldering the factory harness.
Specifications
- Manufacturer: Fuel Injector Clinic
- Part Number: is140-1000h
- Flow Rate: 1000cc/min
- Injector Quantity: 4
- Injector Type: Saturated / high impedance ball and seat
- Impedance: High-Z / high impedance
- Matching Technology: Fuel Injector Clinic Data Match Technology
- Flow Test Pressure: 43.5 PSI (3 Bar)
- Flow Test Fuel Temperature: 90 degrees F
- Calibration Fluid: CF-16B
- Pigtails: PGTUSC4
- Optional Plug-and-Play Adapters: PADPUtoT4
- O-Rings: Included as required for the listed factory application
- Warranty: Lifetime warranty against failure caused by defects in original manufacture
Features
- Complete set of four 1000cc/min performance fuel injectors
- Saturated, high-impedance ball and seat injector design
- Increased fuel capacity for modified and higher-output applications
- Excellent linearity and short pulse width repeatability
- Fuel Injector Clinic proprietary Data Match Technology
- Each injector is individually serial numbered
- Detailed Data Match Sheet provides flow matching and latency information
- Flow tested at 43.5 PSI (3 Bar) and 90 degrees F using CF-16B calibration fluid
- Superior short pulse width control supports precise tuning and strong drivability
- PGTUSC4 solder-in pigtails available with the injector set
- Optional PADPUtoT4 plug-and-play adapters eliminate the need to cut or solder the factory harness
- Brand-new injectors rather than remanufactured or core-program units
- Includes required O-rings for the listed factory application
- Lifetime warranty against failure caused by defects in original manufacture
Data Matched for Consistent Fuel Delivery
Injector capacity is only part of a properly engineered fuel system. Consistency between injectors is critical when tuning a performance engine, which is why Fuel Injector Clinic uses its proprietary Data Match Technology for the is140-1000h set. Each injector is individually serial numbered, and its results are documented on the supplied Data Match Sheet to provide detailed flow matching and latency information for the tuner.
Combined with superior short pulse width control and tight manufacturing tolerances, this matching process helps make the 1000cc injectors easier to tune while maintaining the drivability expected from a properly calibrated street or performance application.
Wiring and Installation
The is140-1000h injector set requires an injector plug conversion when used with the applicable factory harness. PGTUSC4 solder-in pigtails can be used to replace the existing injector plugs, or optional PADPUtoT4 plug-and-play adapters can connect the injectors to the stock harness without cutting or soldering.
Fuel Injector Clinic uses brand-new, unused injectors for its performance applications rather than relying on remanufactured or core-program injectors. The injectors are also configured with the O-rings required for the listed factory application. For aftermarket fuel rails or other nonstandard fuel-system configurations, contact Beefcake Racing before ordering to verify proper fitment.
Fitment
- 2005 Scion tC
- 2006 Scion tC
- 2007 Scion tC
- 2008 Scion tC
- 2009 Scion tC
- 2010 Scion tC
- 2011 Scion tC
- 2012 Scion tC
- 2013 Scion tC
- 2014 Scion tC
- 2015 Scion tC
- 2016 Scion tC
- 2008 Scion xB
- 2009 Scion xB
- 2010 Scion xB
- 2011 Scion xB
- 2012 Scion xB
- 2013 Scion xB
- 2014 Scion xB
- 2015 Scion xB
- Select Toyota Matrix applications utilizing the 1ZZ engine
- Select Toyota Corolla XRS applications utilizing the 1ZZ engine
- Select Toyota MR2-S applications utilizing the 1ZZ engine
- Select Toyota Celica applications utilizing the 1ZZ engine
FAQs
What wiring is required for the Fuel Injector Clinic is140-1000h injector set?
The set uses PGTUSC4 solder-in pigtails for the required injector plug conversion. Optional PADPUtoT4 plug-and-play adapters can be used to connect the injectors to the applicable factory harness without cutting or soldering.
What makes Fuel Injector Clinic Data Match Technology important?
Data Match Technology provides precise matching across the injector set. Each injector is individually serial numbered, and the supplied Data Match Sheet provides detailed flow matching and latency information that can help the tuner achieve consistent fuel delivery and precise calibration.
Why Buy Fuel Injector Clinic Injectors From Beefcake Racing?
Beefcake Racing is your source for Fuel Injector Clinic injectors and the supporting fuel-system components needed for serious street and performance builds. Whether you are upgrading a Scion tC, Scion xB, or compatible Toyota application, our team can help you choose the injector and supporting components appropriate for your combination. Questions about the Fuel Injector Clinic is140-1000h? Email sales@beefcakeracing.com or call 1-855-827-7223.
CA Residents: WARNING: Cancer and Reproductive Harm www.P65Warnings.ca.gov
