Fuel Injector Clinic 365cc Fuel Injector Set - High Z (is140-0365h) - Scion tC / xB / Toyota 1ZZ
Upgrade your Scion or compatible Toyota fuel system with the Fuel Injector Clinic is140-0365h 365cc High-Z fuel injector set. This complete set of four saturated, high-impedance ball and seat injectors is engineered for performance applications that need increased fueling capability along with the precise control required for excellent drivability. Great linearity, short pulse width repeatability, and tight manufacturing tolerances help make these injectors straightforward to tune while delivering consistent fuel control across a wide operating range.
Fuel Injector Clinic precisely flow matches each injector set to within 1 percent. Every injector is individually numbered, with detailed results supplied on the included flow sheet. FIC flow tests and rates these injectors at 43.5 PSI (3 Bar) with fuel at 90 degrees F using CF-16B calibration fluid. PGTUSC4 solder-in pigtails are included for the required connector conversion, or optional PADPUtoT4 plug-and-play adapters can be used to connect the injectors without cutting or soldering the factory harness.
Specifications
- Manufacturer: Fuel Injector Clinic
- Part Number: is140-0365h
- Flow Rate: 365cc/min
- Injector Quantity: 4
- Injector Type: Saturated / high impedance ball and seat
- Impedance: High-Z / high impedance
- Flow Matching: Precisely flow matched to within 1 percent
- Flow Test Pressure: 43.5 PSI (3 Bar)
- Flow Test Fuel Temperature: 90 degrees F
- Calibration Fluid: CF-16B
- Pigtails: PGTUSC4
- Optional Plug-and-Play Adapters: PADPUtoT4
- O-Rings: Included as required for the listed factory application
- Warranty: Lifetime warranty against failure caused by defects in original manufacture
Features
- Complete set of four 365cc/min performance fuel injectors
- Saturated, high-impedance ball and seat injector design
- Excellent linearity for predictable fuel delivery
- Strong short pulse width repeatability for precise low-pulse-width control
- Precisely flow matched to within 1 percent
- Each injector is individually numbered
- Detailed flow sheet included with injector-specific results
- Flow tested at 43.5 PSI (3 Bar) and 90 degrees F using CF-16B calibration fluid
- Tight manufacturing tolerances help provide easier tuning and excellent drivability
- PGTUSC4 solder-in pigtails included
- Optional PADPUtoT4 plug-and-play adapters eliminate the need to cut or solder the factory harness
- Fuel Injector Clinic uses brand-new, unused injectors for its performance applications
- Includes required O-rings for the listed factory application
- Lifetime warranty against failure caused by defects in original manufacture
Precision Flow Matching and Tuning Control
Consistent fuel delivery from cylinder to cylinder is critical to a properly calibrated performance engine. Fuel Injector Clinic precisely flow matches the injectors within each is140-0365h set to within 1 percent. Every injector is individually numbered, and its results are documented on the detailed flow sheet supplied with the set.
Superior short pulse width control and tight manufacturing tolerances give tuners predictable injector behavior throughout the operating range. The result is a 365cc injector set designed to combine increased fueling capability with the drivability needed for a properly tuned street or performance application.
Brand-New Performance Injectors
Fuel Injector Clinic chooses brand-new, unused injectors for its performance applications rather than relying on remanufactured or core-program injectors. This approach eliminates the additional uncertainty that can come with previously used injector components and provides a fresh foundation for a performance fuel system.
Wiring and Installation
The is140-0365h injector set requires an injector plug conversion when installed with the applicable factory wiring harness. Included PGTUSC4 solder-in pigtails can be used to replace the existing injector plugs. For an installation that does not require cutting or soldering the factory harness, optional PADPUtoT4 plug-and-play adapters can be selected instead.
Fuel Injector Clinic configures these injectors with the O-rings required for the listed factory application. If your vehicle uses an aftermarket fuel rail or another unusual or nonstandard fuel-system configuration, contact Beefcake Racing before ordering to verify that you receive the correct injector setup.
Fitment
- 2005 Scion tC
- 2006 Scion tC
- 2007 Scion tC
- 2008 Scion tC
- 2009 Scion tC
- 2010 Scion tC
- 2011 Scion tC
- 2012 Scion tC
- 2013 Scion tC
- 2014 Scion tC
- 2015 Scion tC
- 2016 Scion tC
- 2008 Scion xB
- 2009 Scion xB
- 2010 Scion xB
- 2011 Scion xB
- 2012 Scion xB
- 2013 Scion xB
- 2014 Scion xB
- 2015 Scion xB
- Select Toyota applications utilizing the 1ZZ engine
FAQs
What wiring is required for the Fuel Injector Clinic is140-0365h injector set?
The injectors require a plug conversion when used with the applicable factory harness. PGTUSC4 solder-in pigtails are included, or optional PADPUtoT4 plug-and-play adapters can be used to connect the injectors without cutting or soldering the factory wiring harness.
How are the FIC is140-0365h injectors matched and tested?
Fuel Injector Clinic precisely flow matches each injector set to within 1 percent. Each injector is individually numbered and documented on the included flow sheet. The injectors are flow tested and rated at 43.5 PSI (3 Bar) with fuel at 90 degrees F using CF-16B calibration fluid.
Why Buy Fuel Injector Clinic Injectors From Beefcake Racing?
Beefcake Racing is your source for Fuel Injector Clinic injectors and the supporting fuel-system components needed for performance street and track builds. Whether you are upgrading a Scion tC, Scion xB, or compatible Toyota application, our team can help you choose the injector and supporting components appropriate for your combination. Questions about the Fuel Injector Clinic is140-0365h? Email sales@beefcakeracing.com or call 1-855-827-7223.
CA Residents: WARNING: Cancer and Reproductive Harm www.P65Warnings.ca.gov
