Fore Innovations Demon / Redeye Level 3 Dual Pump Fuel System (97-123) - 2018-2023 Dodge Challenger
The Fore Innovations 97-123 Level 3 Dual Pump Fuel System is a return-style fuel system capable of supporting 1,000+ RWHP for Dodge Challenger Demon, Redeye, Jailbreak, and Super Stock applications, including the Demon 170. Fore recommends operating one pump full time and activating the secondary pump under load. The Level 3 configuration routes the fuel rails in parallel with the multi-port F4i fuel pressure regulator positioned before the rails in a deadhead configuration.
The system includes an in-tank dual pump supply module that retains OE tank transfer, fuel level sender, and EVAP functionality while adding upgraded feed and return lines, Monoblock Hellcat Hemi fuel rails, high-capacity filtration, an FCV check valve, and a multi-port F4i regulator with boost reference.
Features
- Supports 1,000+ RWHP with dual fuel pumps
- Return-style fuel system
- Fore recommends running one pump full time and activating the secondary pump under load
- Fuel rails routed in parallel
- Deadhead fuel system configuration
- Multi-port F4i fuel pressure regulator positioned before the fuel rails
- Boost-referenced fuel pressure regulation
- Monoblock Hellcat Hemi fuel rails
- Retains OE tank transfer functionality
- Retains OE fuel level sender functionality
- Retains OE EVAP functionality
- Upgraded feed and return lines
- High-capacity fuel filtration
- FCV check valve
- E85 capable with the appropriate fuel pumps and filtration
E85 Applications
This fuel system can be configured for E85 by selecting F90000267, F90000274, or F90000285 fuel pumps along with microglass SSD or stainless filtration.
Fore Innovations generally prefers the Level 2 or Level 4 system over the Level 3 configuration for E85 applications because the engine must be able to start on fuel vapor. Engine startup with E85 may be challenging with this configuration and requires additional consideration from the tuner.
Included Components
- Demon/Redeye dual fuel pump module
- FCV check valve
- F4i Fuel Pressure Regulator
- 88mm inline fuel filter
- Monoblock Hellcat Hemi fuel rails
- LX / LC Hellcat OE feed line blockoff cap
- 40 feet of fuel line and 12 hose ends in your selected configuration
- 7 billet low-profile 90-degree O-ring fittings
- 4 straight AN-to-ORB fittings
- 3 -8 ORB plugs
- 1 1.25-inch O-ring port extension
- 1 2.0-inch O-ring port extension
- 10 hose straps and mounting screws
- Fittings, hose, and hardware required for typical fuel line plumbing
Installation & Tuning Requirements
This is a standalone fuel system. Professional installation and a custom tune are required. Qualified installers and tuners must be able to interface the system with the OE wiring harness and FPDM, understand proper component placement and hose routing, and configure factory-like fuel pump prime and on/off operation without generating error codes.
Fore Innovations supplies basic system schematics and detailed component-level instructions and can provide troubleshooting assistance for the performance and function of its fuel system and components. Fore does not provide assistance with tuning or interfacing the system with the OE wiring harness, ECU, or FPDM(s).
Fuel Heat & Fuel Level
This fuel system generates substantially more fuel capacity and heat than the original fuel system. High-performance fuel pumps generate more heat than the factory pump, while the composite fuel tank acts as an insulator and stores heat. The shape of the factory fuel tank also limits the fuel pickup capacity of the system.
The driver must maintain a higher-than-normal fuel level in the tank at all times to help minimize heat-related damage and ensure adequate fuel pickup.
Fitment
- 2018 Dodge Challenger SRT Demon
- 2019 Dodge Challenger SRT Hellcat Redeye
- 2020 Dodge Challenger SRT Hellcat Redeye
- 2020 Dodge Challenger SRT Super Stock
- 2021 Dodge Challenger SRT Hellcat Redeye
- 2021 Dodge Challenger SRT Super Stock
- 2021 Dodge Challenger SRT Hellcat Redeye Jailbreak
- 2022 Dodge Challenger SRT Hellcat Redeye
- 2022 Dodge Challenger SRT Super Stock
- 2022 Dodge Challenger SRT Hellcat Redeye Jailbreak
- 2023 Dodge Challenger SRT Hellcat Redeye
- 2023 Dodge Challenger SRT Super Stock
- 2023 Dodge Challenger SRT Hellcat Redeye Jailbreak
- 2023 Dodge Challenger SRT Demon 170
Available Options and Upgrades
Electrical Options
- None: Base module configuration with approximately 6"" of fuel pump power wire extending from the hermetic seal.
- FC2 Controller with 6-Gauge Wiring: Operates both pumps simultaneously using factory control. Best for two smaller street-duty pumps or two large pumps in track applications where increased fuel heat is less of a concern. Can control secondary pumps on a triple-pump module when a small primary pump is powered by the OEM harness. Includes 14' of 6 AWG power wire, 100-amp fuse, 3' ground wire, 7' 12 AWG pump leads, and sealed Delphi connector.
- FC3 Staged Controller with 4-Gauge Wiring: Independently controls the secondary pump(s) from the primary pump using factory control plus a secondary trigger. Recommended for two or three large pumps in street applications to help minimize fuel heat. Includes 14' of 4 AWG power wire, 100-amp fuse, 3' ground wire, 7' 12 AWG pump leads, and sealed Delphi connector.
- Delphi Connector / Pigtail Only: Includes a sealed Delphi connector and 7' of 12 AWG pump leads. Installer is responsible for supplying and properly configuring the required fuses and relays.
Filtration Media
- Cellulose: 10-micron nominal / 14-micron absolute disposable element with aluminum endcaps and Viton O-ring. For gasoline and race gas. Recommended for Injector Dynamics injectors.
- Microglass SSD Anti-Static: 12-micron absolute disposable, static-dissipating element with aluminum endcaps and Viton O-ring. Compatible with gasoline, race gas, E85, E100, M5, diesel, and other fuel blends. Recommended for Injector Dynamics injectors.
- Stainless: 10-micron nominal / 26-micron absolute reusable stainless element with stainless endcaps and Viton O-ring. Compatible with gasoline, race gas, E85, E100, M5, diesel, and other fuel blends.
Fuel Filter Upgrades
- 128mm Filter: Upgrades the standard 88mm filter to a larger 128mm filter for increased filtration capacity and longer service intervals.
- Billet Mounting Bracket: Provides a secure, show-quality underbody filter installation while keeping the filter accessible for maintenance.
- Filter Monitoring Gauge and Fitting: Monitors fuel pressure before the filter to help identify restriction. Increasing pre-filter pressure can indicate a clogged filter, which can reduce pump performance, shorten pump life, and increase fuel temperature. Includes a fitting for proper gauge orientation.
Additional System Options
- Honeywell Pressure Switch for FC3: 1/8"" NPT male pressure switch designed for installation in the intake manifold. Must receive both boost and vacuum signals.
- Boost / Vacuum Manifold Kit: Includes Fore Innovations Boost / Vacuum Manifold, three 1/4"" barb fittings, and four plugs.
Fuel Pump Warranty:
We take great pride in our product line since we design, machine, assemble, and package our products entirely in house. We guarantee our products to be free of defects in materials and workmanship to the original purchaser. Due to the highly technical nature of our products, we recommend only experienced and competent individuals and shops install our products and systems.
We cannot accept returns on injectors or pumps that have been in contact with fuel.
Fore Innovations, LLC does not warranty any product that have been damaged or rendered defective as a result of accident, misuse, or abuse. Additionally, Fore Innovations is not responsible for special, incidental, or consequential damages or costs incurred due to the installation, use, or misuse of our products.
We will gladly refund any parts that are received in new resalable condition and accompanied with a Return Authorization Number to the original purchaser. Fore Innovations will not be responsible for any items sent to us without a Return Authorization Number.
TI Automotive (and Walbro) fuel pumps are sold only with TI Automotive’s warranty. Currently, TI Automotive does not have a warranty on their high performance parts. For more information:
CA Residents: WARNING: Cancer and Reproductive Harm www.P65Warnings.ca.gov
