Fore Innovations LX/LC Hellcat Level 2 Triple Pump Fuel System (69-132) - 2015-2023 Hellcat
The Fore Innovations LX/LC Hellcat Level 2 Fuel System is a return-style fuel system capable of supporting 1,200+ RWHP with triple fuel pumps. Fore recommends operating one pump full time and activating the secondary pumps under load. Fuel is routed through the billet Hellcat Hemi fuel rails in series, with the boost-referenced F2i Fuel Pressure Regulator installed after the rails.
The in-tank supply system retains the OE fuel transfer system, fuel level senders, and EVAP functionality while adding upgraded feed and return lines, high-capacity filtration, and Fore's high-capacity F2i regulator. This system is designed for 2015-2023 Hellcat applications as well as compatible SRT and R/T vehicles equipped with a Hellcat engine swap.
Features
- Supports 1,200+ RWHP depending on fuel pump configuration and application
- Triple fuel pump configuration
- Fore recommends running one pump full time and activating the secondary pumps under load
- Return-style fuel system
- Fuel rails routed in series
- Boost-referenced F2i Fuel Pressure Regulator installed after the fuel rails
- Billet Hellcat Hemi fuel rails
- Retains OE fuel transfer functionality
- Retains OE fuel level senders
- Retains OE EVAP functionality
- Upgraded feed and return lines
- High-capacity fuel filtration
- Can be configured for E85 with the appropriate fuel pumps and filtration
E85 Applications
This fuel system can be configured for E85 by selecting F90000267, F90000274, or F90000285 fuel pumps along with microglass SSD or stainless filtration.
Included Components
- LX/LC Hellcat triple fuel pump module
- F2i Fuel Pressure Regulator
- 88mm inline fuel filter
- Billet Hellcat Hemi fuel rails
- LX/LC Hellcat OE feed line blockoff cap
- 40 feet of fuel line with matching hose ends in your selected configuration
- 5 billet low-profile 90-degree O-ring fittings
- 5 straight AN-to-ORB fittings
- 2 billet low-profile 180-degree O-ring fittings
- 2 -8 ORB 1.25-inch port extensions
- 1 -8 ORB plug
- 10 hose straps with mounting screws
- Fittings, hose, and hardware required for typical fuel line plumbing
OE Fuel Pressure Sensor Options
By default, this fuel system deletes the OE fuel pressure sensor. Fore Innovations offers additional sensor provisions that must be selected when ordering.
- Delete OE Fuel Pressure Sensor: Removes the factory fuel pressure sensor from the fuel system configuration.
- Inline Aftermarket Sensor: Includes a new AC Delco sensor and provisions for mounting it in a high-flow coupling, along with two additional hose ends. On this Level 2 system, the sensor can be installed without extending the OE electrical harness.
- Regulator Mounted Aftermarket Sensor: Includes a new AC Delco sensor and adapter for mounting the sensor directly to the fuel pressure regulator. The installer must extend the OE electrical harness to accommodate the new sensor location.
Installation & Tuning Requirements
This is a standalone fuel system. Professional installation and a custom tune are required. The qualified installer and tuner must be able to interface the system with the OE wiring harness and FPDM, understand proper component placement and hose routing, and configure factory-like fuel pump prime and on/off operation without generating error codes.
Fore Innovations supplies basic system schematics and detailed component-level instructions and can provide troubleshooting assistance for the performance and function of its fuel system and components.
Fuel Heat & Fuel Level
This system generates substantially more fuel capacity and heat than the original fuel system. High-performance fuel pumps generate more heat than the factory pump, while the composite fuel tank acts as an insulator and can retain that heat. The shape of the factory fuel tank also limits the fuel pickup capacity of the system.
The driver must maintain a higher-than-normal fuel level in the tank to help minimize heat-related damage and ensure adequate fuel pickup.
Fitment
- 2015 Dodge Challenger SRT Hellcat
- 2016 Dodge Challenger SRT Hellcat
- 2017 Dodge Challenger SRT Hellcat
- 2018 Dodge Challenger SRT Hellcat
- 2019 Dodge Challenger SRT Hellcat
- 2020 Dodge Challenger SRT Hellcat
- 2021 Dodge Challenger SRT Hellcat
- 2022 Dodge Challenger SRT Hellcat
- 2023 Dodge Challenger SRT Hellcat
- 2015 Dodge Charger SRT Hellcat
- 2016 Dodge Charger SRT Hellcat
- 2017 Dodge Charger SRT Hellcat
- 2018 Dodge Charger SRT Hellcat
- 2019 Dodge Charger SRT Hellcat
- 2020 Dodge Charger SRT Hellcat
- 2021 Dodge Charger SRT Hellcat
- 2022 Dodge Charger SRT Hellcat
- 2023 Dodge Charger SRT Hellcat
Additional Fitment: Compatible SRT and R/T LX/LC applications equipped with a Hellcat engine swap. Verify fuel system and vehicle compatibility before ordering for engine-swap applications.
Available Options and Upgrades
Electrical Options
- None: Base module configuration with approximately 6"" of fuel pump power wire extending from the hermetic seal.
- FC2 Controller with 6-Gauge Wiring: Operates both pumps simultaneously using factory control. Best for two smaller street-duty pumps or two large pumps in track applications where increased fuel heat is less of a concern. Can control secondary pumps on a triple-pump module when a small primary pump is powered by the OEM harness. Includes 14' of 6 AWG power wire, 100-amp fuse, 3' ground wire, 7' 12 AWG pump leads, and sealed Delphi connector.
- FC3 Staged Controller with 4-Gauge Wiring: Independently controls the secondary pump(s) from the primary pump using factory control plus a secondary trigger. Recommended for two or three large pumps in street applications to help minimize fuel heat. Includes 14' of 4 AWG power wire, 100-amp fuse, 3' ground wire, 7' 12 AWG pump leads, and sealed Delphi connector.
- Delphi Connector / Pigtail Only: Includes a sealed Delphi connector and 7' of 12 AWG pump leads. Installer is responsible for supplying and properly configuring the required fuses and relays.
Filtration Media
- Cellulose: 10-micron nominal / 14-micron absolute disposable element with aluminum endcaps and Viton O-ring. For gasoline and race gas. Recommended for Injector Dynamics injectors.
- Microglass SSD Anti-Static: 12-micron absolute disposable, static-dissipating element with aluminum endcaps and Viton O-ring. Compatible with gasoline, race gas, E85, E100, M5, diesel, and other fuel blends. Recommended for Injector Dynamics injectors.
- Stainless: 10-micron nominal / 26-micron absolute reusable stainless element with stainless endcaps and Viton O-ring. Compatible with gasoline, race gas, E85, E100, M5, diesel, and other fuel blends.
Fuel Filter Upgrades
- 128mm Filter: Upgrades the standard 88mm filter to a larger 128mm filter for increased filtration capacity and longer service intervals.
- Billet Mounting Bracket: Provides a secure, show-quality underbody filter installation while keeping the filter accessible for maintenance.
- Filter Monitoring Gauge and Fitting: Monitors fuel pressure before the filter to help identify restriction. Increasing pre-filter pressure can indicate a clogged filter, which can reduce pump performance, shorten pump life, and increase fuel temperature. Includes a fitting for proper gauge orientation.
Additional System Options
- Honeywell Pressure Switch for FC3: 1/8"" NPT male pressure switch designed for installation in the intake manifold. Must receive both boost and vacuum signals.
- Boost / Vacuum Manifold Kit: Includes Fore Innovations Boost / Vacuum Manifold, three 1/4"" barb fittings, and four plugs.
Fuel Pump Warranty:
We take great pride in our product line since we design, machine, assemble, and package our products entirely in house. We guarantee our products to be free of defects in materials and workmanship to the original purchaser. Due to the highly technical nature of our products, we recommend only experienced and competent individuals and shops install our products and systems.
We cannot accept returns on injectors or pumps that have been in contact with fuel.
Fore Innovations, LLC does not warranty any product that have been damaged or rendered defective as a result of accident, misuse, or abuse. Additionally, Fore Innovations is not responsible for special, incidental, or consequential damages or costs incurred due to the installation, use, or misuse of our products.
We will gladly refund any parts that are received in new resalable condition and accompanied with a Return Authorization Number to the original purchaser. Fore Innovations will not be responsible for any items sent to us without a Return Authorization Number.
TI Automotive (and Walbro) fuel pumps are sold only with TI Automotive’s warranty. Currently, TI Automotive does not have a warranty on their high performance parts. For more information:
CA Residents: WARNING: Cancer and Reproductive Harm www.P65Warnings.ca.gov
