Fore Innovations Fuel System Level 1 Dual Pump 800hp (11-17 Mustang GT) 42-521

products description

800 rwhp capable return fuel system uses the factory fuel rails. The upgraded feed fuel is regulated before entering the factory fuel rails. Proper upgraded feed line and filtration included. Perfect system for applications where factory fuel rails must be used.

Fuel system becomes E85 capable by choosing F90000267, F90000274, F90000285 fuel pumps AND microglass SSD or stainless filtration. We generally prefer the L2 or L4 systems over the L1 (or L3) configuration since the engine must be able to start on fuel vapor. Engine start with E85 may be challenging and will require additional consideration from the tuner.

INCLUDES

S197C Fuel Pump Module (dual pump)
F2i Fuel Pressure Regulator
88mm Inline Fuel Filter
FCV Check valve
All fittings, hose, and hardware necessary to complete typical fuel line plumbing

-25 feet fuel line (your choice)

-Qty 8 compression style billet hose ends

-Qty 4, low profile 90 degree billet o-ring fittings

-Qty 3, straight AN to o-ring fittings

-Qty 8, hose straps with stainless mounting screws

-Qty 1, 3/8 EFI (female) to AN-8 (male) adapter

This is a stand alone fuel system. Professional installation and a custom tune is required. Qualified installers and tuners must be able to interface to the OE harness and FPDM, understand proper component placement, hose routing, and deliver the vehicle with factory-like pump prime/on/off logic with no error codes. Fore Innovations will supply basic system schematics and detailed component level instructions, and can provide troubleshooting of the performance and function of our system and components.

This fuel system generates substantially more heat and capacity than the original fuel system. The high powered fuel pumps make much more heat than the factory pump and the composite fuel tank construction acts as an insulator and stores heat. Additionally, the shape of the factory fuel tank limits the pickup capacity of this fuel system. The user (driver) must keep more fuel (than normal) in the tank at all times to minimize heat damage and ensure adequate fuel pickup

FITS:

2011-2017 Mustang GT or V6 with factory fuel rails

Electrical Upgrade

None: base module configuration, 6" [150mm] of pump power wire protrude from top of hermetic seal

FC2 Controller with 6 gauge wiring:

- Operates both pumps simultaneously, using factory control

- Best for controlling two small fuel pumps for street duty, or two large fuel pumps for track use only (due to fuel heat)

- May be used for control of secondary pumps with triple module IF [a small] primary pump can be run by OEM harness

- Includes 14' [4.2m] of 6 AWG power wire and 100 amp fuse

- Includes 3' [.9m] of 6 AWG ground wire with ring terminal

- Includes 7' [2.1m] 12 AWG pump leads and sealed Delphi connector at pump module

FC3 Staged Controller with 4 gauge wiring:

- Operates secondary pump(s) independently from primary pump using factory control in conjunction with a secondary trigger source.

- Best for controlling two or three large fuel pumps for street duty and minimizing heat

- Includes 14' [4.2m] of 4 AWG power wire and 100 amp fuse

- Includes 3' [.9m] of 4 AWG ground wire with ring terminal

- Includes 7' [2.1m] 12 AWG pump leads and sealed Delphi connector at pump module

Filtration Media

CELLULOSE FILTER ELEMENT

- cellulose element, bonded aluminum endcaps, Viton o-ring

- provides 10 micron nominal, 14 micron absolute filtration

- use with gasoline and race gas

- disposable

- recommended filtration for use with Injector Dynamics fuel injectors

MICROGLASS SSD (ANTI-STATIC) FILTER ELEMENT

- microglass element, static dissipating, bonded aluminum endcaps, Viton o-ring

- provides 12 micron absolute filtration

- use with all fuel types and blends (i.e. gasoline, race gas, E85, E100, M5, diesel)

- disposable

- recommended filtration for use with Injector Dynamics fuel injectors

STAINLESS FILTER ELEMENT

- stainless element, stainless endcaps, Viton o-ring

- provides 10 micron nominal, 26 micron absolute filtration

- use with all fuel types and blends (i.e. gasoline, race gas, E85, E100, M5, diesel)

-re-usable

Fuel Filter Upgrades

Upgrade to 128mm Filter

- Upgrade from standard 88mm filter to 128mm filter length for more filtration capacity and more time between service intervals.

Billet Mounting Bracket

- Use it to mount filter under car body, show quality installation to secure mounting of filter assembly for ease of maintenance

Filter Monitoring Gauge and Fitting

- Use to monitor fuel pressure before filter to inspect filter health. A higher pressure before filter indicates loss across the filter. If ignored, substantial filter obstruction will lead to reduced pump performance, shortened pump life, and higher fuel heat. Fitting is includes to allow precise orientation of pressure gauge.

System Options

Honeywell Pressure Switch for FC3

- 1/8 NPT Male threads, installs in intake manifold, must see boost and vacuum

Boost Vacuum Manifold Kit

- Our Boost / Vacuum manifold kit includes the following: Fore Innovations Boost / Vacuum Manifold (3 x 1/4" barb fittings, 4 x plugs)

Fitment:

- 2011 Mustang GT

- 2012 Mustang GT

- 2013 Mustang GT

- 2014 Mustang GT

- 2015 Mustang GT

- 2016 Mustang GT

- 2017 Mustang GT

Shop all Fore Innovations Fuel Systems at Beefcake Racing, Authorized Dealer, Call 1-855-827-7223 9am-10pm EST for guaranteed lowest price.

CA Residents: WARNING: Cancer and Reproductive Harm www.P65Warnings.ca.gov