Detroit Speed Door Jamb Wiring Boot Kit with Billet Trim - 010421DS
Give the door wiring on your custom build the clean, finished appearance it deserves with the Detroit Speed 010421DS Door Jamb Wiring Boot Kit with Billet Trim. Designed as a universal solution for routing electrical wiring between the body and doors, this kit combines flexible EPDM rubber boots with machined billet aluminum trim for an OE-inspired installation with a custom-built appearance. Instead of leaving wiring exposed or relying on generic pass-through solutions, the Detroit Speed kit protects the wiring while cleaning up an area that can make a noticeable difference in the fit and finish of a high-end build.
The flexible EPDM rubber boots protect wiring as it passes between the body and door while accommodating the movement that occurs every time the door opens and closes. Each boot has an internal diameter capable of accommodating wiring bundles up to 1.30 inches, with a nominal length of 3.5 inches and an installation range of approximately 3 to 4.25 inches. This gives custom builders useful flexibility when determining the ideal mounting locations for their specific vehicle.
The 010421DS version steps up the finished appearance with machined billet aluminum trim rings installed at the boot openings. The kit includes two door jamb wiring boots, four billet trim pieces, and eight stainless steel oval-head mounting screws, providing the components needed to complete both sides of the vehicle. Installation requires a 2 inch opening in the body and custom positioning based on the individual vehicle.
Important installation note: The 010421DS is a universal component and is not designed as a direct-fit kit for any specific make or model. Installation location and available clearance will vary by vehicle, so the installer must determine the proper position before cutting the required openings.
Quick Specs
- Part Number: 010421DS
- Manufacturer: Detroit Speed
- Product Type: Door Jamb Wiring Boot Kit
- Fitment: Universal
- Boot Material: EPDM Rubber
- Trim Material: Billet Aluminum
- Trim Finish: Raw / Machined
- Boot Quantity: 2
- Billet Trim Pieces: 4
- Stainless Steel Oval-Head Mounting Screws: 8
- Required Body Opening: 2 inches
- Maximum Internal Wiring Diameter: Up to 1.30 inches
- Nominal Boot Length: 3.5 inches
- Installation Length Range: Approximately 3 to 4.25 inches
- Designed to Route Wiring Between Body and Doors
- Provides OE-Style Wiring Protection and Appearance
- Mounting Hardware Included
- Custom Installation Required
- Installation Instructions Included
- Emission Code: 4
Features
- Universal solution for routing electrical wiring from the vehicle body into the doors
- EPDM rubber boots provide flexible protection for door wiring
- Helps protect wiring as the door repeatedly opens and closes
- Machined billet aluminum trim gives the installation a clean, custom appearance
- Accommodates wiring bundles up to 1.30 inches in diameter
- 3.5 inch nominal boot length provides flexibility for custom installations
- Approximately 3 to 4.25 inch installation range accommodates varying body-to-door distances
- Includes two EPDM door jamb wiring boots for a complete left- and right-side installation
- Includes four billet aluminum trim pieces
- Includes eight stainless steel oval-head mounting screws
- Requires a 2 inch opening for installation
- Universal design works with custom vehicle builds where an application-specific wiring boot is unavailable
- Combines wiring protection with a finished appearance suitable for detailed custom builds
FAQs
Is the Detroit Speed 010421DS Door Jamb Wiring Boot Kit vehicle-specific?
No. The 010421DS is a universal kit rather than a direct-fit component for a particular vehicle. The mounting position and available clearance must be determined for the specific application, and custom installation is required.
What is included with the Detroit Speed 010421DS kit?
The kit includes two EPDM door jamb wiring boots, four machined billet aluminum trim pieces, eight stainless steel oval-head mounting screws, and installation instructions. The boots accommodate wiring bundles up to 1.30 inches in diameter.
Why Buy From Beefcake Racing?
Beefcake Racing proudly offers genuine Detroit Speed chassis, suspension, body, and fabrication components backed by competitive pricing, fast shipping, and expert technical support. Whether you're wiring a complete custom build, cleaning up a Pro-Touring project, or putting the finishing details on a classic performance car, our knowledgeable team can help you select the right Detroit Speed components for your project.
Questions about installation or application?
Email: sales@beefcakeracing.com
Phone: 1-855-827-7223
CA Residents: WARNING: Cancer and Reproductive Harm www.P65Warnings.ca.gov
