Fuel Injector Clinic 1200cc (130 lbs/hr at OE 58 PSI) Fuel Injector Set - High Z (Jeep 3.6L V6 Engines) (is232-1200h)
Give your Jeep 3.6L V6 the fuel capacity needed for serious performance with the Fuel Injector Clinic 1200cc High-Z Fuel Injector Set. Part number is232-1200h, previously offered as is232-1100h, includes six saturated, high-impedance injectors rated at 1200cc/min (110 lbs/hr) at 43.5 PSI (3 Bar) and 1350cc/min (130 lbs/hr) at the OE 58 PSI (4 Bar) fuel pressure. With substantial flow capability, superior short pulse width control, and Fuel Injector Clinic's advanced Data Match Technology, this matched set delivers the precise and repeatable fuel delivery needed for accurate tuning and excellent drivability.
Fuel Injector Clinic precisely matches the is232-1200h set using its proprietary Data Match Technology. Each injector is individually serial numbered, and the included Data Match Sheet provides detailed flow matching and latency information for the specific injectors in your set. FIC flow tests and rates these injectors at 43.5 PSI (3 Bar) with fuel temperature maintained at 90 degrees F using CF-16B calibration fluid. PGTJETR6Q solder-in pigtails are included, while optional PADPJtoU6 plug-and-play adapters provide an installation option that does not require cutting or soldering the factory wiring harness.
Specifications
- Manufacturer: Fuel Injector Clinic
- Part Number: is232-1200h
- Previous Part Number: is232-1100h
- Injector Quantity: 6
- Flow Rating at 43.5 PSI: 1200cc/min (110 lbs/hr)
- Flow Rating at OE 58 PSI: 1350cc/min (130 lbs/hr)
- OE Fuel Pressure: 58 PSI (4 Bar)
- Injector Type: Saturated / high impedance
- Matching: Fuel Injector Clinic Data Match Technology
- FIC Test Pressure: 43.5 PSI (3 Bar)
- Test Fuel Temperature: 90 degrees F
- Calibration Fluid: CF-16B
- Included Wiring: PGTJETR6Q solder-in pigtails
- Optional Wiring Adapter: PADPJtoU6 plug-and-play adapters
- Seals: Includes the O-rings required for the listed factory application
- Warranty: Lifetime warranty against failure caused by defects in original manufacture
Features
- Six 1200cc high-impedance fuel injectors for Jeep 3.6L V6 engines
- Flows 1200cc/min (110 lbs/hr) at 43.5 PSI (3 Bar)
- Flows 1350cc/min (130 lbs/hr) at the OE 58 PSI (4 Bar) fuel pressure
- Previously offered under part number is232-1100h
- High-flow design provides increased fueling capacity for performance applications
- Proprietary Data Match Technology provides precise injector set matching
- Each injector is individually serial numbered for identification and documentation
- Includes a Data Match Sheet with detailed flow matching and latency information
- Superior short pulse width control supports precise low-flow fueling and excellent drivability
- State-of-the-art matching helps provide predictable injector behavior for accurate tuning
- Flow tested and rated at 43.5 PSI (3 Bar) with fuel temperature maintained at 90 degrees F
- Testing performed using CF-16B calibration fluid
- Includes PGTJETR6Q solder-in pigtails for injector connector conversion
- Optional PADPJtoU6 plug-and-play adapters eliminate the need to cut or solder the factory wiring harness
- Supplied with the O-rings required for the listed factory application
- Uses brand-new, unused injectors rather than remanufactured or core-program injectors
- Covered by Fuel Injector Clinic's lifetime warranty against defects in original manufacture
Wiring and Installation
The is232-1200h injector set requires an injector connector change when installed with the included PGTJETR6Q pigtails. The pigtails can be soldered into the vehicle's wiring harness to replace the existing injector connectors. For an installation without cutting or soldering the factory harness, optional PADPJtoU6 plug-and-play adapters can be used instead.
Fuel Injector Clinic uses brand-new, unused injectors for its performance applications rather than relying on remanufactured or core-program injectors. The injectors are configured with the O-rings required for the listed factory application. If your Jeep uses an aftermarket fuel rail or another non-standard fuel system configuration, contact Beefcake Racing before ordering to verify proper injector fitment.
Fitment
- Jeep 3.6L V6 Engines
FAQs
Why is the is232-1200h rated at both 1200cc and 1350cc?
Injector flow changes with fuel pressure. Fuel Injector Clinic rates this injector at 1200cc/min (110 lbs/hr) at its standard 43.5 PSI (3 Bar) test pressure. At the Jeep application's OE 58 PSI (4 Bar) fuel pressure, the injector flows 1350cc/min, or 130 lbs/hr.
Do the Fuel Injector Clinic is232-1200h injectors require a wiring change?
Yes, when using the included PGTJETR6Q solder-in pigtails. For an installation without cutting or soldering the factory wiring harness, optional PADPJtoU6 plug-and-play adapters can be used instead.
Why Buy Fuel Injector Clinic Injectors From Beefcake Racing?
Beefcake Racing specializes in high-performance fuel system upgrades and can help you select the right injectors and supporting components for your Jeep 3.6L V6 build. Whether you have questions about injector sizing, fuel pressure, wiring adapters, tuning requirements, or compatibility with an aftermarket fuel system, our performance specialists can help you choose the correct components for your combination.
Email: sales@beefcakeracing.com
Phone: 1-855-827-7223
CA Residents: WARNING: Cancer and Reproductive Harm www.P65Warnings.ca.gov
