Fuel Injector Clinic 1200cc-D (130 lbs/hr at OE 58 PSI) Fuel Injector Set - High Z (Jeep 3.6L V6 Engines) (is232-1200h-d)
Give your Jeep 3.6L V6 the fuel capacity and precise control needed for a serious performance combination with the Fuel Injector Clinic 1200cc-D High-Z Fuel Injector Set. Part number is232-1200h-d includes six saturated, high-impedance injectors rated at 1200cc-D/min (110 lbs/hr) at 43.5 PSI (3 Bar) and 1350cc/min (130 lbs/hr) at the OE 58 PSI (4 Bar) fuel pressure. Combining substantial flow capability with superior short pulse width control and advanced Data Match Technology, this injector set is engineered to provide the consistent, predictable fuel delivery tuners need for performance applications while maintaining excellent drivability.
Fuel Injector Clinic precisely matches the is232-1200h-d set using its proprietary Data Match Technology. Each injector is individually serial numbered, and the included Data Match Sheet provides detailed flow matching and latency information for the specific injectors in the set. FIC flow tests and rates these injectors at 43.5 PSI (3 Bar) with fuel temperature maintained at 90 degrees F using CF-16B calibration fluid. State-of-the-art matching and superior short pulse width control help make these injectors easier to tune while providing consistent fuel delivery from low pulse width operation through higher-load conditions.
Specifications
- Manufacturer: Fuel Injector Clinic
- Part Number: is232-1200h-d
- Injector Quantity: 6
- Flow Rating at 43.5 PSI: 1200cc-D/min (110 lbs/hr)
- Flow Rating at OE 58 PSI: 1350cc/min (130 lbs/hr)
- OE Fuel Pressure: 58 PSI (4 Bar)
- Injector Type: Saturated / high impedance
- Matching: Fuel Injector Clinic Data Match Technology
- FIC Test Pressure: 43.5 PSI (3 Bar)
- Test Fuel Temperature: 90 degrees F
- Calibration Fluid: CF-16B
- Seals: Includes the O-rings required for the listed factory application
- Warranty: Lifetime warranty against failure caused by defects in original manufacture
Features
- Six 1200cc-D high-impedance fuel injectors for Jeep 3.6L V6 engines
- Flows 1200cc-D/min (110 lbs/hr) at 43.5 PSI (3 Bar)
- Flows 1350cc/min (130 lbs/hr) at the OE 58 PSI (4 Bar) fuel pressure
- High-flow design provides increased fueling capacity for performance applications
- Proprietary Data Match Technology provides precise injector set matching
- Each injector is individually serial numbered for identification and documentation
- Includes a Data Match Sheet with detailed flow matching and latency information
- Superior short pulse width control supports precise low-flow fueling and excellent drivability
- State-of-the-art matching helps provide predictable injector behavior for accurate tuning
- Flow tested and rated at 43.5 PSI (3 Bar) with fuel temperature maintained at 90 degrees F
- Testing performed using CF-16B calibration fluid
- Supplied with the O-rings required for the listed factory application
- Covered by Fuel Injector Clinic's lifetime warranty against defects in original manufacture
Precision Matched for Accurate Tuning
The is232-1200h-d set uses Fuel Injector Clinic's Data Match Technology to provide detailed characterization of the injectors rather than simply grouping injectors by nominal flow rating. Each injector is individually serial numbered, and its matching and latency information is supplied on the Data Match Sheet. This detailed injector data, combined with superior short pulse width control, gives tuners the information and predictable injector behavior needed to develop an accurate calibration while maintaining strong drivability.
Fuel Injector Clinic configures these injectors with the O-rings required for the listed factory application. If your Jeep uses an aftermarket fuel rail or another non-standard fuel system configuration, contact Beefcake Racing before ordering to verify proper injector fitment.
Fitment
- Jeep 3.6L V6 Engines
FAQs
Why is the is232-1200h-d rated at both 1200cc-D and 1350cc?
Injector flow changes with fuel pressure. Fuel Injector Clinic rates this injector at 1200cc-D/min (110 lbs/hr) at its standard 43.5 PSI (3 Bar) test pressure. At the Jeep application's OE 58 PSI (4 Bar) fuel pressure, the injector flows 1350cc/min, or 130 lbs/hr.
How are the Fuel Injector Clinic is232-1200h-d injectors matched?
Fuel Injector Clinic uses its proprietary Data Match Technology to precisely match the injector set. Each injector is individually serial numbered, and the included Data Match Sheet provides detailed flow matching and latency information to support accurate calibration and consistent fuel delivery.
Why Buy Fuel Injector Clinic Injectors From Beefcake Racing?
Beefcake Racing specializes in high-performance fuel system upgrades and can help you select the right injectors and supporting components for your Jeep 3.6L V6 build. Whether you have questions about injector sizing, fuel pressure, tuning requirements, or compatibility with an aftermarket fuel system, our performance specialists can help you choose the correct components for your combination.
Email: sales@beefcakeracing.com
Phone: 1-855-827-7223
CA Residents: WARNING: Cancer and Reproductive Harm www.P65Warnings.ca.gov
